User manual WHIRLPOOL ADN 039 INSTRUCTION FOR USE

[. . . ] - 20 ÷ + 50 °C 1550 x 550 x 950 mm. 87 Kg 1520 x 580 x 1000 mm 110 Kg Power supply Power consumption Sleeve shape 0, 14 Kw Table 1 Kw Vacuum motor Pump motor Steam pressure Steam consumption Sound intensity level Working temperature Working humidity Storing temperature Net dimension Net weight Overall dimensions (packaging included) Gross weight (packaging included) WARNING: The machine must not be supplied with different voltages than those indicated on the table. 2 5 MACHINE COMPONENTS The following are the main machine components: 3 Pos. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 ARTICLE 534269 Z01L10 Z23C00 43H009 07A001 39H011 39B005 43G007 173441 43A020 301016 Z18M00 35A004 38S001 43G006 213123 161020 274102 274122 37B002 274203 175005 161037 24A011 162114 39B002 39H011 Z07A00 244235 212061 212060 212063 07A002 38W001 DESCRIPTION Antenna for cable Steam iron type U Electric cable Iron plug by Ilme Steam tube Coil for steam iron solenoid valve Steam solenoid valve for iron Iron socket by Ilme Small control case for 2nd iron fitting 2nd iron switch Power supply inlet Connector Complete fitting for second iron Pressure gauge Safety valve Socket for heated shape by Ilme Table heater 1000 Watt Perforated plate for universal table Cloth for univ. table with GB zip fastener Padding and net for universal table Gate valve for boiler exhaust Cloth for garment tray Garment tray Stainless steel rail Or-ring Universal table Solenoid valve for steam gun Coil for steam gun solenoid valve Steam gun Flange gasket Ø135mm Boiler heater 3, 9 kW Boiler heater 3, 3 kW Boiler heater 4, 8 kW Steam tube out of silicone Check valve Pos. [. . . ] ATTENTION: After having carried out all the electrical connections, make sure that the cables are protected against any possible hits and are suitably fixed and isolated. 6. 4 WATER CONNECTION AND BOILER EXHAUST Connect the water pipes to the cable passage Ø12 of the machine. Install an on-off valve and a filter on the water inlet, which has to be closed each evening, in order to avoid any water sucks into the boiler. Connect the gate valve of the boiler exhaust (with a G 3/8” threading) to the drainage system. 7 7. 1 INSTRUCTIONS FOR USE PUTTING INTO OPERATION • • • • • The whole unit can be used, opened and repaired by qualified technicians only. It is forbidden to use the machine if flooded by liquids or in particularly aggressive or explosive/inflammable places. Do not ignore the dangers for the operator’s health and follow the hygienic and safety regulations. Check that the electrical wiring is carried out correctly according to the current regulations, and that the fuse blocks are closed and complete of fuses. USE • • • • • • • • • • • Open the on-off valve of the water supply. The warning light of the water supply switches on automatically (the water starts running into the boiler). Once the water has reached the required level the relevant warning light switches off automatically, whereas the one of the boiler heater turns on. After a few minutes the boiler reaches the working pressure of 2. 6 bar (check the pressure on the pressure gauge), the relevant warning light switches off automatically. The generator is now ready to supply steam. Adjust the board temperature by means of the thermostat wheel. Wait until the boards reach the required temperature. Push the pedal to put the air suction on boards into operation. At the end of the work, turn off the table by means of the relevant buttons. USE OF THE SLEEVE SHAPE • By drawing the sleeve shape towards the ironing surface, the valve on the inside will open automatically. Push the pedal for the vacuum operation. USE OF THE STEAM IRON TYPE ”U” • Turn on the iron switch. 8 7. 2 7. 3 7. 4 • • 7. 5 • • • • Switch on the iron a few minutes before you start working, until the soleplate has reached the adjusted temperature. In case the temperature of the soleplate has to be kept very high, we recommend to apply a Teflon® shoe in order to prevent burns of the garment. USE OF THE STEAM-AIR GUN Place the garment to be treated onto the spotting shape, making sure that it lies exactly on the vacuum part. [. . . ] The guarantee is extended as it follows: In case of malfunction of the machinery contact the manufacturer and quote the trouble, the model, serial number and the operating conditions of the machine. At the receipt of the machine and after an accurate analysis, the manufacturer reserves the right to repair or to replace the product. If the machine is still under guarantee, the manufacturer will repair or replace it free, but if the returned product is not defective, the manufacturer reserves the right to charge the freight to the customer (transport, etc. ). This warranty must be considered annulled in case of damages caused by an incorrect use, negligence, wear and tear, chemical corrosion, installation in contrast with the operating instructions. [. . . ]