User manual WHIRLPOOL ADN 554 INSTRUCTION FOR USE

[. . . ] 3C MEDIDAS Capacité et écart entre les grilles Capacidad y distancia (paso) entre las fuentes 67 mm ISTRUZIONI PER L’INSTALLATORE NOTICE POUR L'INSTALLATEUR SIMPLE INSTRUCCIONES PARA EL INSTALADOR INSTRUCTIONS FOR THE INSTALLER ANLEITUNGEN FÜR DEN INSTALLATEUR Convection with humidification models 5 x 2/3 GN / 5-10 x 1/1 GN / 5 x (60x40) n° 05 x 2/3 GN n° 5 x 1/1 GN 7 ISTRUZIONI PER L’INSTALLATORE NOTICE POUR L'INSTALLATEUR SIMPLE INSTRUCCIONES PARA EL INSTALADOR INSTRUCTIONS FOR THE INSTALLER ANLEITUNGEN FÜR DEN INSTALLATEUR Convection with humidification models 5 x 2/3 GN / 5-10 x 1/1 GN / 5 x (60x40) n° 10x 1/1 GN n°5 x (60x40) n°4 x 1/1 GN 8 ISTRUZIONI PER L’INSTALLATORE NOTICE POUR L'INSTALLATEUR SIMPLE INSTRUCCIONES PARA EL INSTALADOR INSTRUCTIONS FOR THE INSTALLER ANLEITUNGEN FÜR DEN INSTALLATEUR Convection with humidification models 5 x 2/3 GN / 5-10 x 1/1 GN / 5 x (60x40) 1. 0 INSTALLING THE APPLIANCE Read this handbook through carefully as it provides important information to guarantee a safe installation, use and maintenance. The appliance must be installed only and exclusively by qualified personnel following the instructions given herein and in compliance with current laws in force. The gas system, water, electricity and the premises on which the appliances are installed comply with the relative installation and safety standards. [. . . ] The specifications of the flexible cable for the electrical connection should be no lower than those of the type with rubber insulation H07 RN-F, with the cross section of the wires as given in the technical data. Install a circuit breaker of a suitable capacity upstream from the appliance, making sure it Fig. 2A has an opening between the contacts of at least 3-mm. 2) for this to which the earth wire is to be connected purpose the relative terminal with the symbol is on the terminal board. The effectiveness of the equipotential system of which the appliance is part of, must conform to current standards. Connect using the screw you find near the power cable’s relief cable strain, marked with the word EQUIPOTENTIAL. The Manufacturer declines all and every responsibility if this important accident prevention norm is not complied with 2. 2A CHECKING MOTOR ROTATION DIRECTION (only for three-phase motors). Check that the fans’ rotation direction is the same as that of the arrow on the stainless steel air-conveying panel, located inside the oven. If they are rotating in the opposite direction, reverse two phases on the supply terminal board. 3) The ovens have a water inlet coupling at the back. Always install an on-off valve between the appliance and the water mains, making sure it is easy to operate. We also suggest installing a cartridge filter on the water inlet pipe. The solenoid valve (A) supplies the steam generation system into the cooking chamber by means of the injector (B) The water must be suitable to human use with the following characteristics: Temperature: included between 15 – 20 °C In case the oven is supplied without steam condensation system (OPTIONAL) inside the drain pipe, the plumbing connection must be done with hot water at a max. Total hardness: included between 4 and 8 °French degree, it is advisable to install a softener upstream from the appliance that will maintain the hardness level at the mentioned values. The oven’s running with water that has a higher hardness level will not be long before scale forms on the walls of the oven and in this case the technical assistance required to repair such damage is not covered by the guarantee. pressure: included between 100 and 200 KPa (1 – 2 bar). Attention higher water pressure values result in increased water consumption and can compromise the correct functioning of some components. Attention: Water treatment systems that bring to different values to the ones above mentioned automatically invalidate the guarantee. The use of dosing systems designed to prevent the build-up of lime-scale in pipes (i. Polyphosphate dosing systems) is also prohibited since it may impair the performance of the appliance. 4A) Drainage for the water is at the back of the oven and must be connected directly to the end of the stainless steel drainpipe. [. . . ] 0F Door microswitch: it stops the oven working when the door is opened. 0G Thermostat system for condensation of discharge steam (Optional): it comprises a solenoid valve controlled by a thermostat whose sensor is housed in contact with the discharge. The solenoid valve, via the injector (G), lets cold water into the drainpipe to condense the steam when a temperature of 90°C is reached, (Fig. 0H Oven relief valve (Optional): (Optional) its job is to adjust humidity inside the cooking chamber . [. . . ]