User manual WHIRLPOOL ADN 600 INSTRUCTION FOR USE

[. . . ] 0802_GB_42 Instructions for installation, use e maintenance GAS KITCHENS ADN 644 · ADN 645 ADN 600 · ADN 601 ADN 602 · ADN 603 04/2008 CHARACTERISTICS Supplied by: Date: Customer Service: FAX e-mail 0802_GB_42 - GAS KITCHENS 04/2008 2 · 16 INDEX 1 2 3 Diagram Characteristics of the appliances Technical data 4 6 6 8 8 8 8 8 8 8 8 8 8 8 8 8 9 9 9 9 9 9 9 9 10 10 10 10 10 11 11 11 11 11 11 11 11 6 Instructions for use 6. 1 Safety, cleaning and repair rules 6. 2 Start-up 6. 2. 1 Lighting and disconnecting flame burner without pilot 6. 3 Lighting and shutdown of electric oven GN 1/1 6. 4 Turning the appliance off in case of breakdown 6. 4. 1 What to do in case of failure 6. 4. 2 What to do in case of prolonged period of disuse 6. 5 Appliance care and frequency of maintenance 6. 6 Recommendations for handling “stainless steel” industrial kitchens 6. 6. 1 Useful information on “stainless steel” 6. 6. 2 Warnings and advice for maintenance of “stainless steel” appliances 6. 6. 3 WEEE Directive 7 Appendix: Electrical diagrams 12 12 12 12 12 12 12 12 12 13 13 13 14 15 4 Installation instructions 4. 1 Safety rules 4. 2 Structure, framework and safety devices of the appliances 4. 2. 1 Cooking zone 4. 2. 2 Oven Electric version GN 1/1 ventilated 4. 3 Assembly 4. 3. 1 Installation premises 4. 3. 2 Statutory regulations and technical requirements 4. 3. 3 Installation 4. 3. 4 Gas connection 4. 3. 5 Smoke extraction 4. 3. 6 Electrical connection 4. 3. 7 Equipotential 5 Operation preparation 5. 1 Preparation and Start-up 5. 1. 1 Start-up 5. 1. 2 Check of power 5. 1. 3 Checking the input pressure 5. 1. 4 Power check with volumetric method 5. 1. 5 Power check for operation with liquid gas 5. 1. 6 Operation control 5. 1. 7 Operator training 5. 1. 8 Conversion and adjustment 5. 1. 9 Replacement of open flames injectors 5. 1. 10 Setting reduced capacity power 5. 2 Maintenance 5. 3 Replacing parts 5. 3. 1 Open flame gas cock 5. 3. 2 Open flame gas burner 5. 3. 3 Open flame thermocouple 5. 3. 4 Open flame plug 5. 3. 5 Heating element of electric oven GN 1/1 5. 3. 6 Fan electric oven GN 1/1 0802_GB_42 - GAS KITCHENS 04/2008 3 · 16 1 - DIAGRAM ADN 645 600 ADN 644 60 34 34 27 27 346 27 69 50 430 535 Data plate 86 30 38 42 240. 8 34 200 400 Data plate 600 70 400 600 0 0 0 0 Gas 1/2" Gas 1/2" 0 0 27 546 Gas 1/2" 50 176. 5 34 50 Gas 1/2" 176. 5 600 178. 5 245 178. 5 245 150 300 600 150 Data plate 200 ADN 601 1000 0 0 0 0 0 0 ADN 600 800 700 Gas 1/2" 0 0 0 0 657 45 910 Gas 1/2" 34 34 45 34 45 710 Gas 1/2" 276. 5 45 34 38 545 Data plate 55 276. 5 700 245 178. 5 Data plate 200 300 1000 300 200 178. 5 245 700 Data plate 200 800 400 200 0802_GB_42 - GAS KITCHENS 04/2008 4 · 16 150 678 60 42 1 - DIAGRAM ADN 603 1000 42 42 Electric power Gas 1/2" ADN 602 Electric power 0 0 0 0 0 0 0 0 0 0 0 Gas 1/2" 738 0 738 690 150 657 150 45 910 Gas 1/2" Electric power 79 34 79 45 45 710 Gas 1/2" 79 34 79 45 38 545 Data plate 55 34 Electric power 276. 5 34 276. 5 700 245 178. 5 Data plate 200 300 1000 300 200 178. 5 245 700 Data plate 200 800 400 200 0802_GB_42 - GAS KITCHENS 04/2008 5 · 16 150 678 60 42 800 700 2 - CHARACTERISTICS OF THE APPLIANCES These appliances are used for professional purposes. Installation, repair and use must be carried out by expert personnel. These instructions for installation are for our gas kitchens set up for the category in the table 1 on pag. The data plate is located on the appliance, see diagram. [. . . ] To replace the fan remove the back unscrew the sight screws, disconnect the wires from the motor, from the inside of the chamber remove the rear bulkhead fan cover and the fan (pos. Re-install in reverse order positioning in the correct way the seal protection (pos. 2) and power mains. 5. 3. 1 Open flame gas cock Loosen the fitting of the pipes (pos. 1) of the thermocouple, unscrew the two screws (pos. 1) fixing the cock on the gas piping through the hanger (pos. 1) install in reverse order install paying attention to the seal ring. After the replacement check the seal using a leack detetctor spray. 5. 3. 2 Open flame gas burner Remove with the help of a screwdriver the spring (pos. 1) blocking the gas pipe and slip off it from burner seat, unscrew the screws (pos. 1), pull down the cup, unfix the thermocouple and the plug (pos. 1) and replace the piece install in reverse order. After replacement, check injector, see table 1 and do a seal check using a leak detector spray. Fig. 2A 0 50 300 100 25 0 15 0 2 0802_GB_42 - GAS KITCHENS 11 · 16 200 1 3 04/2008 6 - INSTRUCTIONS FOR USE 6. 1 Safety, cleaning and repair rules • This appliance is used for the preparation of meals at industrial level. Usage and cleaning can be carried only by expert personnel. Maintenance and repair can be carried out only by skilled technical personnel. • These indications must be communicated to all those concerned during internal training. This appliance must be constantly watched over when being used!• Grease and overheated oil can catch fire. Use this appliance only under constant control. Never use water to put out grease or oil!Cover with a lid, turn off the hot plate and remove pot from the burner. • Do not leave the burners running. For proper use, pots should not be bigger than the flames. [. . . ] If no specific cleaning recommendations are available, it is necessary, however, to use detergents having a low chloride content. After cleaning, remove all soap residues with plenty of clean water and thoroughly dry the surfaces. • Minimize contact of “stainless steel” with concentrated acids, spices, salts, etc. Even acid vapours coming from cleaning the tiles favour “stainless steel” corrosion. [. . . ]