User manual WHIRLPOOL ADN 608 INSTRUCTION FOR USE

[. . . ] 0803_GB_42 Instructions for installation, use e maintenance GAS KITCHENS WITH PILOT ADN 606 · ADN 607 ADN 608 · ADN 610 ADN 609 · ADN 611 ADN 631 04/2008 CHARACTERISTICS Supplied by: Date: Customer Service: FAX e-mail 0803_GB_42 - GAS KITCHENS WITH PILOT 04/2008 2 · 20 INDEX 1 2 Diagram Characteristics of the appliances 4 7 7 9 9 9 9 9 9 9 9 9 9 9 10 10 10 10 10 10 10 10 10 10 10 12 12 12 12 12 12 12 12 12 12 12 12 12 13 13 13 13 13 13 13 13 13 13 14 14 14 6 Instructions for use 15 6. 1 Safety, cleaning and repair rules 15 6. 2 Start-up 15 6. 2. 1 Lighting and disconnecting flame burner with pilot 15 6. 3 Lighting and shutdown of electric oven GN 2/1 15 6. 4 Lighting and shutdown of electric oven GN 1/1 16 6. 5 Lighting and shutdown of gas oven GN 2/1 16 6. 5. 1 Lighting the pilot gas oven GN 2/1 16 6. 5. 2 Lighting the main burner and temperature adjustment gas oven GN 2/1 16 6. 6 Lighting and shutdown of solid top 16 6. 7 Turning the appliance off in case of breakdown 16 6. 7. 1 What to do in case of failure 16 6. 7. 2 What to do in case of prolonged period of disuse 16 6. 8 Appliance care and frequency of maintenance 16 6. 9 Recommendations for handling “stainless steel” industrial kitchens 17 6. 9. 1 Useful information on “stainless steel” 17 6. 9. 2 Warnings and advice for maintenance of “stainless steel” appliances 17 6. 9. 3 WEEE Directive 17 7 Appendix: Electrical diagrams 18-19 3 Technical data 4 Installation instructions 4. 1 Safety rules 4. 2 Structure, framework and safety devices of the appliances 4. 2. 1 Cooking zone 4. 2. 2 Oven Gas version GN 2/1 Electric version GN 2/1 Electric version GN 1/1 ventilated 4. 3 Assembly 4. 3. 1 Installation premises 4. 3. 2 Statutory regulations and technical requirements 4. 3. 3 Installation 4. 3. 4 Gas connection 4. 3. 5 Smoke extraction 4. 3. 6 Electrical connection 4. 3. 7 Equipotential 5 Operation preparation 5. 1 Preparation and Start-up 5. 1. 1 Start-up 5. 1. 2 Check of power 5. 1. 3 Checking the input pressure 5. 1. 4 Power check with volumetric methodo 5. 1. 5 Power check for operation with liquid gas 5. 1. 6 Operation control 5. 1. 7 Check of pilot flame 5. 1. 8 Checking the primary air 5. 1. 9 Operator training 5. 1. 10 Conversion and adjustment 5. 1. 11 Replacement of open flames injectors 5. 1. 12 Replacement of pilot injectors of open flames 5. 1. 13 Setting reduced capacity power 5. 1. 14 Replacement of solid top injectors 5. 1. 15 Replacement of burner injector of gas oven GN 2/1 5. 1. 16 Replacement of pilot injector of gas oven GN 2/1 5. 2 Maintenance 5. 3 Replacing parts 5. 3. 1 Open flame gas cock 5. 3. 2 Open flame thermocouple 5. 3. 3 Gas valve gas oven GN 2/1 5. 3. 4 Plug gas oven GN 2/1 5. 3. 5 Thermocouple gas oven GN 2/1 5. 3. 6 Main burner gas oven GN 2/1 5. 3. 7 Cock solid top 5. 3. 8 Plug solid top 5. 3. 9 Thermocouple solid top 5. 3. 10 Heating elements of electric oven GN 2/1 5. 3. 11 Heating elements of electric oven GN 1/1 5. 3. 12 Fan electric oven GN 1/1 0803_GB_42 - GAS KITCHENS WITH PILOT 04/2008 3 · 20 1 - DIAGRAM ADN 607 1000 0 0 0 0 0 0 ADN 606 800 700 0 0 0 0 Gas 1/2" Gas 1/2" 678 496 45 910 Gas 1/2" 34 34 45 34 45 710 Gas 1/2" 276. 5 45 34 25 545 Data plate 55 276. 5 700 245 178. 5 Data plate 200 300 1000 300 200 178. 5 245 700 Data plate 200 800 400 200 0 0 0 0 0 0 Electric power Gas 1/2" Electric power 0 0 0 0 0 Gas 1/2" 0 690 496 45 910 Gas 1/2" Electric power 79 34 79 45 45 710 34 79 45 25 545 Data plate 55 Gas 1/2" 34 Electric power 276. 5 79 34 276. 5 700 245 178. 5 Data plate 200 300 1000 300 200 178. 5 245 700 Data plate 200 800 400 200 0803_GB_42 - GAS KITCHENS WITH PILOT 4 · 20 150 678 60 42 1000 800 700 150 60 42 04/2008 1 - DIAGRAM ADN 611 1000 Electric power 0 0 0 0 0 0 ADN 609 Electric power 0 0 0 0 0 0 Gas 1/2" Gas 1/2" 0 0 690 496 45 910 Gas 1/2" Electric power 79 34 79 45 45 710 Gas 1/2" 79 34 79 45 25 545 Data plate 55 34 Electric power 276. 5 34 276. 5 700 245 178. 5 178. 5 245 700 Data plate 200 300 1000 300 200 Data plate 200 800 400 200 ADN 610 1000 ADN 608 800 700 60 42 55 150 678 456 Gas 1/2" 45 910 34 45 34 45 710 45 496 Gas 1/2" 276. 5 34 700 276. 5 245 178. 5 Data plate 200 300 1000 300 200 178. 5 245 700 0803_GB_42 - GAS KITCHENS WITH PILOT 123 456 7 123 0 0 0 0 0 0 7 0 0 0 0 Gas 1/2" 25 545 Data plate Gas 1/2" 34 Data plate 200 800 400 200 5 · 20 150 678 60 42 800 700 04/2008 1 - DIAGRAM ADN 631 800 700 60 496 45 710 Gas 1/2" 34 45 34 545 25 Data plate 55 700 Data plate 800 0803_GB_42 - GAS KITCHENS WITH PILOT 123 456 7 0 0 0 Gas 1/2" 678 150 04/2008 6 · 20 2 - CHARACTERISTICS OF THE APPLIANCES These appliances are used for professional purposes. Installation, repair and use must be carried out by expert personnel. These instructions for installation are for our gas kitchens set up for the category in the table 1 on pag. The data plate is located on the appliance, see diagram. [. . . ] 3) install in reverse order. 5. 3. 6 Main burner gas oven GN 2/1 Remove the front/lower panel by removing the fastening screws. Unscrew the screws fixing the hanger (pos. 3) and extract the injector-holder from its housing, unscrew the screws rear fixing (pos. 3) of the burner and put in a new piece in the reverse order. After the replacement check the seal using a leack detector spray. 5. 3 Replacing parts All parts must be replaced by authorized technicians only!To replace the following parts first remove all the control knobs and control panel (after loosening the fixing screws), then extract the ignition wire. 5. 3. 7 Cock solid top Loosen the fitting of the pipes (pos. 2) fixing the cock on the gas piping and replace the piece (pos. After the replacement check the seal using a leack detector spray. 5. 3. 1 Open flame gas cock Loosen the fitting of the pipes (pos. 1) fixing the cock on the gas piping and replace the piece (pos. After the replacement check the seal using a leack detector spray. 5. 3. 8 Plug solid top Remove the solid top, the flame spreader and the burner body, unscrew the screw (pos. 2) pull out the spring using a pointed tool, remove the ignition plug from the bottom, disconnect the ignition lead and insert a new plug. 5. 3. 2 Open flame thermocouple Loosen the nut (pos. 1) for fastening the thermocouple on the valve and on the burner (pos. 1) install in reverse order. 5. 3. 9 Thermocouple solid top Loosen the nut (pos. 2) for fastening the thermocouple on the valve and the screw (pos. After any maintenance or repair work, replace the control panel and the lower panel. After replacing gas input components, check operation again and test for leakage. 5. 3. 3 Gas valve gas oven GN 2/1 Loosen the fittings (pos. 4) which are for the connection for the gas pipe and the thermocouple, remove the coil of the thermostat from its place in the cooking chamber and put in a new piece in the reverse order. After the replacement check the seal using a leack detector spray. 0803_GB_42 - GAS KITCHENS WITH PILOT 04/2008 13 · 20 5 - SET-UP FOR OPERATION Fig. 4 3 6 2 4 5 5 67 1 7 1 5. 3. 10 Heating elements of electric oven GN 2/1 Unplug the appliance from the electrical mains!5) element is attached to the top of the cooking chamber. To remove the heating elements, unscrew the screw that attach themto the corresponding flange, pull the heating elements and relative wires forward. Use a screwdriver to disconnect the wires and install a new heating element in reverse order. 5. 3. 11 Heating element of electric oven GN 1/1 Unplug the appliance from the electrical mains! [. . . ] A on the adhesive label featuring the technical specifications applied on the actual product (the label also giving the serial number). This symbol indicates that the product is classified, according to the regulations in force, as an item of electrical and electronic equipment and conforms to EU Directive 2002/96/EC (WEEE) meaning that, at the end of its service life, it must be treated separately from domestic waste, i. e. it must be handed in free of charge to a separate waste electrical and electronic equipment collection centre or returned to the reseller when buying a new equivalent item of equipment. The user is responsible for delivering the unit at the end of its life to the appropriate collection facilities. Failure to do so shall result in the user being subject to the penalties prescribed by the legislation in force on waste. [. . . ]