User manual WHIRLPOOL ADN 634 INSTRUCTION FOR USE

[. . . ] 0804_GB_42 Instructions for installation, use e maintenance GAS FRY TOP ADN 632 · ADN 633 ADN 634 · ADN 635 04/2008 CHARACTERISTICS Supplied by: Date: Customer Service: FAX e-mail 0804_GB_42 - GAS FRY TOP 04/2008 2 · 12 INDEX 1 2 3 Diagram Characteristics of the appliances Technical data 4 5 5 6 6 6 6 6 6 6 6 6 7 7 7 7 7 7 8 8 8 8 8 8 8 9 9 9 9 9 9 9 9 10 10 10 10 10 10 10 10 10 11 11 11 11 4 Installation instructions 4. 1 Safety rules 4. 2 Structure, framework and safety devices of the appliances 4. 3 Assembly 4. 3. 1 Installation premises 4. 3. 2 Statutory regulations and technical requirements 4. 3. 3 Installation 4. 3. 4 Gas connection 4. 3. 5 Smoke extraction 5 Operation preparation 5. 1 Preparation and Start-up 5. 1. 1 Start-up 5. 1. 2 Check of power 5. 1. 3 Checking the input pressure 5. 1. 4 Power check with volumetric method 5. 1. 5 Power check for operation with liquid gas 5. 1. 6 Operation control 5. 1. 7 Checking the primary air 5. 1. 8 Operator training 5. 1. 9 Conversion and adjustment 5. 1. 10 Replacement of burner injector fry top 400 5. 1. 11 Replacement of burner injectors fry top 600 5. 1. 12 Setting reduced capacity power 5. 2 Maintenance 5. 3 Replacing parts 5. 3. 1 Gas cock 5. 3. 2 Thermocouple 5. 3. 3 Plug 5. 3. 4 Burner fry top 400 5. 3. 5 Burner fry top 600 6 Instructions for use 6. 1 Safety, cleaning and repair rules 6. 2 Start-up 6. 2. 1 Lighting and disconnecting of burner 6. 3 Cleaning and taking care of the machine 6. 4 Turning the appliance off in case of breakdown 6. 4. 1 What to do in case of failure 6. 4. 2 What to do in case of prolonged period of disuse 6. 5 Appliance care and frequency of maintenance 6. 6 Recommendations for handling “stainless steel” industrial kitchens 6. 6. 1 Useful information on “stainless steel” 6. 6. 2 Warnings and advice for maintenance of “stainless steel” appliances 6. 6. 3 WEEE Directive 0804_GB_42 - GAS FRY TOP 04/2008 3 · 12 1 - DIAGRAM ADN 634 ADN 635 400 ADN 632 ADN 633 400 700 60 Gas 1/2" Gas 1/2" 0 0 657 45 510 34 45 45 310 34 45 545 38 Data plate 55 Gas 1/2" 34 Gas 1/2" 34 700 Data plate 700 Data plate 600 400 0804_GB_42 - GAS FRY TOP 4 · 12 150 04/2008 678 2 - CHARACTERISTICS OF THE APPLIANCES These appliances are used for professional purposes. Installation, repair and use must be carried out by expert personnel. These instructions for installation are for our gas fry top set up for the category in the table 1 on pag. The data plate is located on the appliance, see diagram. [. . . ] 1) from the piezo ignition, unscrew the screw (pos. 1) fixing the support thermocouple /plug (pos. 1) on the combustion chamber and pull down the support to a more convenient position, unscrew the screw (pos. 1) install in reverse order. 5. 3. 4 Burner fry top 400 Unscrew the screws (pos. 2A) fixing the burner to the injector-holder nut (pos. 2A) and on the combustion chamber, lift up the burner (pos. 2A) for pull off from the injector-holder, pull off and put in a new piece in the reverse order. After the replacement check the seal using a leack detector spray. 0804_GB_42 - GAS FRY TOP 04/2008 9 · 12 6 - INSTRUCTIONS FOR USE 6. 1 Safety, cleaning and repair rules • This appliance is used for the preparation of meals at industrial level. Usage and cleaning can be carried only by expert personnel. Maintenance and repair can be carried out only by skilled technical personnel. • These indications must be communicated to all those concerned during internal training. This appliance must be constantly watched over when being used!• Grease and overheated oil can catch fire. Use this appliance only under constant control. Never use water to put out grease or oil!• Do not leave the burners running. • Parts of the appliance and attachments exposed to food must be cleaned with detergents and rinsed thoroughly with potable water. • Do not clean the appliance using water jets or steam, whether direct or pressurized!• If the room is being cleaned with water/steam jets or high-pressure equipment, it is necessary to switch off the appliance first!• Before starting to clean the appliance, disconnect from the mains. • Do not use inflammable liquid to clean the appliance. • Repairs may be carried out only by skilled personnel. [. . . ] Failure to do so shall result in the user being subject to the penalties prescribed by the legislation in force on waste. Suitable separated collection so that the unit no longer used can be sent off for environmentally compatible recycling, treatment and disposal helps avoid possible negative effects on the environment and on health and facilitates the recycling of the product's component materials. For more detailed information on available collection systems, contact the local waste disposal service or the shop you purchased the unit from. Producers and importers fulfil their responsibility for environmentally compatible recycling, treatment and disposal both directly and by joining a collective scheme. 6. 6. 2 Warnings and advice for maintenance of “stainless steel” appliances • “Stainless” steel equipment surfaces must be kept clean and in contact with air at all times. [. . . ]