User manual WHIRLPOOL ADP 6342 A PC IX PRODUCT FICHE

[. . . ] The corresponding indicator lamp lights up. “Change programme in progress” Select additional options Press the Start button The selected programme is then memorised (even in the event of power failure). Press the START button for 2 sec. until the Start indicator lamp switches off. Select another programme and press the START button again. Wash cycle - Only open the dishwasher if necessary (Warning: beware of hot steam). [. . . ] Only after the START button has switched off: Press the ON / OFF button. Warning: When the door is opened steam comes out!Unload the appliance, starting from the lower rack. Switch off the appliance Turn off the water tap, unload the racks Dishwasher loading instructions and racks provided depending on the model Upper rack: Crockery holder (A): Depending on the position, for long-handles utensils, cups and plates. carving forks, knives) must be arranged with the sharp end facing in towards the appliance. B A C D Half Load: Load the upper rack (see description of Options). Place the cutlery basket (C), if provided, in the upper rack. Rack height adjustment (also when loaded): Pull the two rack handles (D) outwards and lower the rack. Pull the two rack handles (D) upwards until the rack Upper adjustment: clicks into place (factory setting). Lower adjustment: D Retainer open Retainer closed Removing the top rack to provide clearance for large items of crockery in the bottom rack: Open the rack guide retainers (E) on the right and left and remove the top rack. When the upper rack is in place the retainers must always be closed. E E Lower rack: Depending on the model with fixed or tilting plate holders (F). Half Load: Load the lower rack (see description of Options). Greater washing power, particularly for plates and saucepans. F H F Cutlery basket (G): Grid (H) to keep items separate. Sharp knives and forks that might cause injury must be placed in the cutlery basket with the sharp end facing downwards. G C Only use dishwasher-proof crockery and dishes. Do not use the appliance for items not suitable for washing in a dishwasher, for example wooden items, aluminium, tin, hand-decorated crockery (unglazed), silver cutlery. What to do if. . . If a fault occurs, before contacting our After-Sales Service, make the following checks to try and remedy the problem (* see also the corresponding chapter in the user instructions). Problem The appliance is not working Cause • No water supply. Press the START button for 2 seconds, until the START indicator lamp switches off. Select a new programme and press the Start button again. If after carrying out the above checks the malfunction persists or appears again, turn the appliance off and turn off the water supply tap, then call our After-Sales Service (see guarantee). Before contacting our After-Sales Service, take note of the following: • The nature of the fault • The appliance type and model • The service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side. Before using the dishwasher, read the user instructions! ADP 1830/6 Quick Reference Guide GB Options 3) Programme selection button Time and failure display Indicates in hours the time remaining until the start of the wash cycle. Switches off when the programme starts and indicates the time remaining in hours and minutes. “F Identification of faults for service technician . . . . ” “Delayed start” button On / Off button The wash cycle can be programmed to start after 1 - 24 hours. With each successive touch of the button, the delayed start indicator increases by 1 hour, and after 24 returns to 00. The dishwasher will start at the set time. “Half load - Multizone” button Start button Switches “on” when the dishwasher is operating. Switches off at the end of the programme. This function can be used with any programme. Press once = upper rack (the symbol comes on) Press twice = lower rack (the symbol comes on) Press 3 times = Off (half load function deactivated). When washing without the top rack, press the “Half Load” button twice, or “Lower rack wash” (relative symbol lights up). [. . . ] When washing without the top rack, press the “Half Load” button twice, or “Lower rack wash” (relative symbol lights up). Antibacterial rinse 4) 5) This function adds an antibacterial rinse at the end of the wash cycle, thereby guaranteeing a perfectly clean and sanitized load. The lamp will light up when the function is activated. If the temperature is not maintained during the antibacterial cycle (e. g. [. . . ]