User manual WHIRLPOOL ADP 6543 PRODUCT FICHE

[. . . ] • The inlet hose must be securely clamped to the water tap to prevent leaks. • The inlet water temperature varies according to the model installed. Inlet hose marked “25°C Max”: maximum temperature 25°C. All other models: maximum temperature 60°C. [. . . ] Make sure the water inlet hose is of the correct type. Refer to the “Connections” chapter in these user instructions. Disposal: The appliance is built from reusable materials. If you decide to scrap the dishwasher, it must be disposed of in compliance with local waste disposal laws. Before scrapping, cut off the power cable so that the appliance cannot be connected to the mains. • To prevent situations of potential danger to children (e. g. danger of suffocation), break the lock of the door so that it can no longer be closed. Child safety: • Children must not be allowed to play with the dishwasher. • Store the detergent, rinse aid and salt in a dry place out of the reach of children. Safety warnings: • The open dishwasher door can only support the weight of the loaded rack when pulled out. Do not rest objects on the open door or sit or stand on it: the appliance may topple over!If the water hardness level does not correspond to position 3 on the selector (factory setting) or if the water hardness level changes: Turn the selector to the correct position (for dishwashers without salt sensor only): Set the water hardness by turning the selector (if fitted) inside the door (top left) using a screwdriver. Use the table below to set the dial to the correct setting: Hardness level German degrees °dH 0-5 6 - 10 11 - 15 16 - 21 22 - 28 29 - 35 36 - 60 French degrees °fH 0-9 10 - 18 19 - 27 28 - 37 38 - 50 51 - 63 64 - 107 mmol/l Clarke scale or English degrees °eH 0 - 6. 3 7 - 12. 6 13. 3 - 18. 9 19. 6 - 25. 9 26. 6 - 35 35. 7 - 44. 1 44. 8 - 74. 9 Setting For dishwashers without salt sensor only! In appliances provided with a salt sensor, the selector automatically turns to the correct position. 1 soft 1 - 2 medium 2 average 3 medium-hard 4 hard 4 very hard 4 extremely hard 0 - 0, 9 1. 0 - 1. 8 1. 9 - 2. 7 2. 8 - 3. 7 3. 8 - 5. 0 5. 1 - 6. 3 6. 4 - 10. 7 0 1 2 3 4 5 6 If the water hardness level falls within category 1 (soft), no salt is required. How to fill the salt container Warning: Only use regeneration salts for use in domestic dishwashers!Do not fill the salt container with unsuitable substances, such as detergent, as this will cause irreparable damage to the water softener system. Unscrew the cap by turning it counter-clockwise. When first using the dishwasher: fill the salt container to the rim with water. Fill the salt container to the rim with salt (using the filler provided) (when filling for the first time use min. Screw the cap back on by turning it clockwise. If regeneration salt is to be added, immediately start a wash programme (rinsing alone is not sufficient) in order to eliminate any residual saline solution straight away and avoid corrosion. Salt level indicator The dishwasher is equipped with an electric or visual salt level indicator (depending on the model installed). Electric indicator The salt level indicator lamp on the control panel lights up when the salt container is empty. Visual indicator The float is clearly visible in the cap window when the salt container is full. [. . . ] Do not use more than the amount of detergent that is recommended. Observe the manufacturer's safety warnings. Keep these products out of reach of children. If you use detergents in tablet form, follow the manufacturer's directions for use. [. . . ]