User manual WHIRLPOOL AGB 405/WP INSTRUCTION FOR USE

[. . . ] In fase di programmazione, uno o più step possono non apparire, se non sono pertinenti al ciclo: ad esempio, non è presente lo step di detergenti in un ciclo di centrifuga. Modificare un ciclo significa: - cancellare uno degli step in sequenza - inserire uno step, tra gli step già in sequenza - modificare i parametri di uno step (vedi par. Esempio 2: si voglia inserire uno step di detergente, dopo il secondo step di carico, nel ciclo LAVAGGIO 2. Si può ipotizzare che un ciclo di lavaggio debba essere composto, mettendo in sequenza alcuni step, nel seguente modo: - step 1: scarico acqua (ad esempio, fino a 5 centimetri) - step 2: carico acqua (ad esempio, fino a 15 centimetri) - step 3: carico detersivi (ad esempio, per 30 secondi) - step 4: riscaldamento (ad esempio, fino a 45°C) - step 5: durata lavaggio (ad esempio, per 5 minuti) Si ipotizzi infine che durante l’esecuzione del ciclo, il tipo motore sia il nr. [. . . ] To enter programming, open door, display shows “DOOR OPEN”, press “MENU”, display shows “PASSWORD”, press 6 times on “START”. display shows “PROGRAMMES SET-UP/MODIFICATION” . Use “+” & “-“ to scroll main menu until display shows “CYCLES SET-UP/MODIFICATION. press “ENTER” , display shows “PRE-WASH”. Use “+” & “-“ to scroll all cycles until display shows “WASH”, press “ENTER” , display shows “WASH1”, use “+” & “-“ to scroll stored cycles until display shows “WASH4” , press “ENTER”, display shows “WASH4: STEP 1 DRAIN”. Use “+” & “-“ to scroll steps in sequence, until display shows “WASH4 STEP2 LOAD”, press “ENTER” to select it, display shows “MODIFY”, press “ENTER” to modify step parameters. display shows “WASH4 STEP2 LOAD MOTOR TYPE”. Use “+” & “-“ to scroll step parameters until display shows “WASH4: STEP2 LOAD LEVEL”. Once required level is reached, please confirm by pressing “ENTER”. display shows “STEP MODIFIED: CONFIRM?€ Press “ENTER” to confirm or “STOP” to abort modification, press then “MENU” more times to scroll upwards to other menus. Also, pls bear in mind that cycles are composed by a step series. We may suppose that a washing cycle consists of the following steps: Step1 – water drain (up to 5 cms) Step2 – water load (up to 15 cms) Step3 – detergents load (i. 5 mins) Suppose now during the cycle operation the motor be the n° 1 (see paragraph n° 31), and that the rotation speed be of 40 min. In this example, the machine, during the operation, behaves in the following way: it makes sure it does not have water inside the drum, then fill up the drum with water. It pours the detergent and proceed to the heating. Once it reaches the temperature wanted it flaps for about 5 minutes. We clarify that, before to start the programming, it is necessarily to have a clear idea on how it must be composed the new cycle and which are the operations that the machine has to execute. Then we start the programming of the new cycle inserting the step sequence wanted. To enter into the programming open the door. Use the keys “+” or “-“ to select from the menu the operation “ CREATION/MODIFY CYCLES”. Use the key “+” or “-“ to select from the cycle menu the cycle that we want to create. [. . . ] Through 2nd soap compartment or from detergent pump no. Rinse with cold water up to 18 cms level Type motor 1 RINSE 3 3 mins. Rinse with cold water up to 18 cms level detergent loaded for 30 secs. *NOTE: in low spin washing machines, the maximum speed is 500 rpm. [. . . ]