User manual WHIRLPOOL AGB 424/WP INSTRUCTION FOR USE

[. . . ] The tank is heated by stainless steel burners (4), resistant to thermal stress and shock. The pilot burner is fitted with fixed nozzles. The combustion chamber and the flue pipes are in electrogalvanised stainless steel plate. The temperature is regulated by means of a thermostat, which controls the ignition and turning off of the burners. [. . . ] The following are the operating pressure tolerances to obtain the nominal power according to the agreed nozzles: - from 15 to 22. 5 mbar for gases of the second family; - from 25 to 35 mbar for gases of the third family (propane). The appliance will not work outside the above pressure thresholds. E= Capacity Heat value Capacity should only be measured when the appliance is at a standstill. The heat value can be obtained from your local Gas Board. from natural to LP, or to another gas group, consult the “TECHNICAL DATA” table to determine the correct nozzles to use. The nozzles for the main burners for different types of gas, marked in 100ths of mm, are in a case supplied with the appliance. When the appliance has been transformed or adapted, recheck its functions as described in paragraph "Checking the functions", page 9. REPLACING PARTS All parts must be replaced by authorised technicians only!To replace the following parts, remove the control panel (after unscrewing its fixing screws). It is advisable to empty the tank. Replacing the pilot burner nozzle (Fig. 2) To change nozzle 30, loosen the fixing screws of the front instrument panel. 12 wrench, unscrew the nozzle from the nozzle holder; replace with a new nozzle (see “TECHNICAL DATA” table). Gas electrovalve (1 - Fig. 1) Unscrew the fitting (3, 16, 21, 17) and loosen the fixing screws. The valve may now be removed and replaced with a new one. Replace and screw down all parts in the correct order. 2 30 28 31 Burner (31 - Fig. 2) Unscrew the nut 29 and remove the nozzle-holder 28. Loosen the screw fixing the burner to the chamber Replace the burner. 2) Unscrew the nipple fixing the thermocouple to the valve, loosen the 2 screws on the pilot burner and replace the thermocouple. To simplify the operation (and all those concerning the pilot burner), screws may be removed and the pilot burner moved to a more accessible position. 29 36 35 043- 03 - Gasfry-pan 9 USING THE APPLIANCE Attention! - Beware of inexpert handling!- The main burner only ignites if the tank is positioned correctly on the heating chamber. Attention! Do not open the cock if the tank is not in the correct operating position. Never overfill the tank. Preparation for use Before frying for the first time, it is advisable to thoroughly clean the appliance and above all the tank (see paragraph "Taking care of the appliance frequency of maintenance", page 11). Special precautions The grills, particularly those with the pan bottom not in stainless steel, are treated in the factory with mineral oil to protect them from rust. The oil should be carefully removed before heating the pan, using hot water and detergent, not chlorine based (less than 30 ppm). After washing, rinse with cold water and heat to 300°C to dry, with the thermostat at the maximum . When the thermostat shuts down, the oven is ready for cooking or, after protecting the bottom with a layer of grease or cooking oil, ready to rest (after use). [. . . ] A on the adhesive label featuring the technical specifications applied on the actual product (the label also giving the serial number). This symbol indicates that the product is classified, according to the regulations in force, as an item of electrical and electronic equipment and conforms to EU Directive 2002/96/EC (WEEE) meaning that, at the end of its service life, it must be treated separately from domestic waste, i. e. it must be handed in free of charge to a separate waste electrical and electronic equipment collection centre or returned to the reseller when buying a new equivalent item of equipment. The user is responsible for delivering the unit at the end of its life to the appropriate collection facilities. [. . . ]