User manual WHIRLPOOL AGB 433/WP INSTRUCTION FOR USE

[. . . ] THE APPLIANCE MUST BE INSTALLED BY QUALIFIED PERSONNEL. FRYER Model Dim. : LxWxH 400 x 900 x 875 600 x 900 x 875 AGB 433/WP AGB 437/WP AGB 435/WP AGB 439/WP 400 x 900 x 875 800 x 900 x 875 400 x 900 x 875 800 x 900 x 875 400 x 900 x 270 600 x 900 x 270 AGB 441/WP AGB 445/WP AGB 443/WP AGB 447/WP 400 x 900 x 270 800 x 900 x 270 400 x 900 x 530 800 x 900 x 530 Voltage rating 230 V 3 / 400 V 3N 230 V 3 / 400 V 3N 230 V 3 / 400 V 3N 230 V 3 / 400 V 3N 230 V 3 / 400 V 3N 230 V 3 / 400 V 3N 230 V 3 / 400 V 3N 230 V 3 / 400 V 3N 230 V 3 / 400 V 3N 230 V 3 / 400 V 3N 230 V 3 / 400 V 3N 230 V 3 / 400 V 3N Power 7. 5 kW 15. 0 kW 12. 0 kW 24. 0 kW 15. 0 kW 30. 0 kW 7. 5 kW 15. 0 kW 12. 0 kW 24. 0 kW 15. 0 kW 30. 0 kW Lead wire / Section 4 x 2. 5 mm2 o 5 x 1. 5 mm2 4 x 6 mm2 o 5 x 2. 5 mm2 4 x 6 mm2 o 5 x 2. 5 mm2 4 x 10 mm2 o 5 x 6 mm2 4 x 6 mm2 o 5 x 2. 5 mm2 4 x 10 mm2 o 5 x 6 mm2 4 x 2. 5 mm2 o 5 x 1. 5 mm2 4 x 6 mm2 o 5 x 2. 5 mm2 4 x 6 mm2 o 5 x 2. 5 mm2 4 x 10 mm2 o 5 x 6 mm2 4 x 6 mm2 o 5 x 2. 5 mm2 4 x 10 mm2 o 5 x 6 mm2 019- 03 - Electric fryer 5 INSTALLATION INSTRUCTIONS Before beginning installation, remove all packaging from the appliance. Some parts are protected with an adhesive film which should be carefully removed. Any remnants of glue should be thoroughly cleaned using suitable substances such as benzine. Under no circumstances should abrasive substances be used. [. . . ] The appliance should be fitted following the indications given in the drawing below. 1 RETRO BACK ARRIERE RÜCKSEITE Unipotential The appliance must be connected up to a unipotential system. The connection screw is located underneath the appliance, on the right hand side. Legal and technical requisites When installing the appliance, the following safety standards must be adhered to: The manufacturers cannot be held responsible for any damage due to inadequate or incorrect installation. Under such circumstances the guarantee will be considered null and void. - Local accident prevention standards - Current CEI standards. Start-up Before using the appliance for the first time, thoroughly clean out the oil bath (see paragraph entitled “Cleaning and Taking Care of the Appliance”). Check that the appliance is connected up properly and start according to instructions overleaf. 019- 03 - Electric fryer 6 USING THE APPLIANCE Warning! - Beware of inexpert handling!- Old and dirty oil or frying fat can represent a real fire hazard; make sure only new oil or frying fat are used each time you start frying. - The food you intend to fry should always be dry; wet food causes the oil to foam and overflow. - Frying excessively large quantities of food at a time also causes the oil to foam; never exceed 1. 5 kg. - If the level of oil in the bath falls below the low level mark stamped on it, the risk of fire will increase. - Never leave the appliance on without any oil in it. The lid delivered with the appliance should always be kept within easy reach. In case of fire, it should be used to douse the flames. CLEANING AND TAKING CARE OF THE MACHINE Warning! Never clean the appliance with jets of water, whether direct or pressurised. Allow the machine to cool down before cleaning Before starting to clean the appliance, disconnect from the mains. Using the hook provided (see drawing 2), you can lift out the elements to make cleaning the appliance easier and far more thorough. Lift the elements as far as they will go. To lower them after cleaning, pull out the button on the left hand side. All steel parts should be washed in warm water, using a neutral detergent, then rinsed thoroughly to eliminate any residual detergent. Avoid using abrasive or corrosive detergents which could damage the steel. Ignition Check that the oil drain release is closed. Fill the bath with oil up to the level marked. Turn on the main switch upstream of the appliance. [. . . ] Failure to do so shall result in the user being subject to the penalties prescribed by the legislation in force on waste. Suitable separated collection so that the unit no longer used can be sent off for environmentally compatible recycling, treatment and disposal helps avoid possible negative effects on the environment and on health and facilitates the recycling of the product's component materials. For more detailed information on available collection systems, contact the local waste disposal service or the shop you purchased the unit from. Producers and importers fulfil their responsibility for environmentally compatible recycling, treatment and disposal both directly and by joining a collective scheme. 019- 03 - Electric fryer 8 Wiring diagrams AGB 433/WP - AGB 435/WP AGB 441/WP - AGB 443/WP 1 2 3 R 11 12 13 mC C2 B2 F2 C1 B1 F1 H2 H1 mA 1 2 3 4 5 6 400 V 3N L1 L 2 L 3 N PE 6 2 4 1 3 5 mA 1 2 3 4 5 6 mC 1 2 3 4 L1 L 2 L 3 230 V 3 mA mC B1 B2 C1 C2 F1 F2 H1 H2 R Line input terminal board Commutating terminal board Switch Microswitch Safety contactor Adjusting contactor Adjusting thermostat Safety thermostat Green pilot lamp Orange pilot lamp Resistance PE 019- 03 - Electric fryer 9 Wiring diagrams AGB 437/WP - AGB 439/WP AGB 445/WP - AGB 447/WP V U W R V U W R Y X Z Y X Z mC mC C2 C2 B2 B2 F2 F2 C1 C1 B1 F1 B1 F1 H2 H1 H2 H1 mA 1 2 3 4 5 6 400 V 3N L1 L 2 L 3 N PE 6 2 4 1 3 5 mA 1 2 3 4 5 6 mC 1 2 3 4 L1 L 2 L 3 230 V 3 mA mC B1 B2 C1 C2 F1 F2 H1 H2 R Line input terminal board Commutating terminal board Switch Microswitch Safety contactor Adjusting contactor Adjusting thermostat Safety thermostat Green pilot lamp Orange pilot lamp Resistance PE 019- 03 - Electric fryer 10 WARNING THE MANUFACTURER CANNOT BE HELD RESPONSIBLE FOR ANY INACCURACIES IN THIS BOOKLET DUE TO COPYING OR PRINTING ERRORS. [. . . ]