User manual WHIRLPOOL AGB 453/WP INSTRUCTION FOR USE

[. . . ] THE APPLIANCE MUST BE INSTALLED BY QUALIFIED PERSONNEL. 3 - TECHNICAL DATA Model Dim. : LxWxH Voltage rating Power Lead wire / Section 400 x 900 x 875 800 x 900 x 875 AGB 453/WP AGB 454/WP 400 x 900 x 270 800 x 900 x 270 230 V 230 V 230 V 230 V 1. 0 kW 2. 0 kW 1. 0 kW 2. 0 kW 3 x 1. 5 mm2 3 x 2. 5 mm2 3 x 1. 5 mm2 3 x 2. 5 mm2 017- 03 - Electric Bain-Marie 5 INSTALLATION INSTRUCTIONS INSTALLATION Before beginning installation, remove all packaging from the appliance. Some parts are protected with an adhesive film which should be carefully removed. Any remnants of glue should be thoroughly cleaned using suitable substances such as benzine. [. . . ] The manufacturers decline all responsibility where poor performance is due to incorrect installation in disregard of the above conditions. Warning! In compliance with international regulations, when connecting the appliance to the mains power supply, a device with a minimum aperture of 3 mm between contacts must be fitted upstream of the appliance, allowing omnipolar disconnection of the appliance from the mains. Wiring When choosing the lead wire, make sure it has the following characteristics: it should be at least of the H07 RNF type and its section should be large enough for the appliance (see "Technical specifications and dimensions", page 5). The cable inlet and terminal board are to be found on the mains supply box, situated near the front left foot. Pass the wire through the core hitch and wire clamp, plug the leads into their terminals on the board and secure them. The earth lead must be a little longer than the others so that it is the last lead to disconnect if the wire clamp breaks. Legal and technical requisites When installing the appliance, the following safety standards must be adhered to: - Local accident prevention standards - Current CEI standards. Unipotential The appliance must be connected up to a unipotential system. The connecting screw is placed on the mains supply box and is marked with a plaque. Plumbing connection The 12 mm ø fitting for the water inlet is placed underneath to the right. To connect, use the pipe fitting supplied with the appliance, taking into account that a 3/8” female is to be inserted. The outlet has a 3/4” male connection located near the inlet. Warning! The manufacturers cannot be held responsible for any damage due to inadequate or incorrect installation. Under such circumstances the guarantee will be considered null and void. 017- 03 - Electric Bain-Marie 6 USING THE APPLIANCE Warning! - Beware of inexpert handling!- Never leave the appliance on without any water in it. The 2002/96/EC (WEEE) Directive: information to users This informational note is meant only for owners of equipment marked with the symbol shown in Fig. A on the adhesive label featuring the technical specifications applied on the actual product (the label also giving the serial number). This symbol indicates that the product is classified, according to the regulations in force, as an item of electrical and electronic equipment and conforms to EU Directive 2002/96/EC (WEEE) meaning that, at the end of its service life, it must be treated separately from domestic waste, i. e. it must be handed in free of charge to a separate waste electrical and electronic equipment collection centre or returned to the reseller when buying a new equivalent item of equipment. The user is responsible for delivering the unit at the end of its life to the appropriate collection facilities. Failure to do so shall result in the user being subject to the penalties prescribed by the legislation in force on waste. Suitable separated collection so that the unit no longer used can be sent off for environmentally compatible recycling, treatment and disposal helps avoid possible negative effects on the environment and on health and facilitates the recycling of the product's component materials. For more detailed information on available collection systems, contact the local waste disposal service or the shop you purchased the unit from. [. . . ] Avoid using abrasive or corrosive detergents which could damage the steel. What to do if not using the appliance for a long time Thoroughly clean and dry the machine as described. Disconnect the power supply. What to do if something goes wrong If anything goes wrong, immediately turn the appliance off, then turn off the power supply at the switch located upstream of the appliance, and call the aftersales department. MAINTENANCE All maintenance should be carried out by qualified personnel only. Before carrying out any maintenance work, unplug the appliance or turn off the switch upstream of the appliance. 017- 03 - Electric Bain-Marie 7 Wiring diagrams AGB 453/WP H1 H2 R1 B1 F1 mA 1 2 3 230 V L1 N PN AGB 454/WP H1 H2 R1 R1 B1 F1 mA 1 2 3 230 V L1 N PN mA H1 H2 R1 B1 F1 Line input terminal board Green pilot lamp Orange pilot lamp Resistance Switch Thermostat 017- 03 - Electric Bain-Marie 8 WARNING THE MANUFACTURER CANNOT BE HELD RESPONSIBLE FOR ANY INACCURACIES IN THIS BOOKLET DUE TO COPYING OR PRINTING ERRORS. [. . . ]