User manual WHIRLPOOL AGB 505/WP INSTRUCTION FOR USE

[. . . ] VALIDITY 006_03 FROM SERIAL NUMBER 70500783 07/2007 Installation, operating and maintenance instructions ELECTRIC TILTING COOKER AGB 505/WP AGB 507/WP INDEX Models and dimensions General reminders and notes General reminders Technical data Construction Laws, technical prescriptions and directives Special requirements for the installation site Positioning, installation and maintenance Positioning Installation Electrical connections and equipotential bonding Connection to waterworks Commissioning and testing Maintenance of the appliance 6 Wiring diagrams 6 6 6 Warning 12 Replacement of heating element Control knob 10 11 11 5 5 5 5 5 page 3 Possible failures and their elimination page 6 7 7 7 7 7 7 7 8 8 8 9 4 Use and cleaning 4 4 5 Warnings and hints for user Instructions for use Switch on, start of cooking and switch off Special precautions Cleaning and care of the appliance Daily cleaning Special procedures in case of long inactivity Special procedures in case of failures How to proceed, if… WEEE Directive 006- 03 - Electric tilting cooker 2 Validity from serial number 70500783 Models and dimensions AGB 505/WP - AGB 507/WP 1110 945 E T A 165 35 480 53 695 53 50 330 525 220 370 125 800 TAE- Technical data plate Water connection D. 12mm Electrical connection 700 006- 03 - Electric tilting cooker 3 120 Validity from serial number 70500783 230 900 210 GENERAL REMINDERS AND NOTES - Read the warnings contained in this manual carefully as they provide important information concerning safety during the installation, use and maintenance of the appliance. - Only personnel trained for its specific use should use the equipment. - Keep the appliance under control during use. - The appliance should be used only for the purpose for which it has been specifically designed; other uses are improper and hence dangerous. [. . . ] - It is also advisable to apply for a maintenance contract with the customer. POSSIBLE FAILURES AND THEIR ELIMINATION Warning!: Only technically qualified service centres can perform the operations described below!Warning!: Before resetting the safety thermostat, it is always necessary to eliminate the problem causing its activation! Even a normal use of the appliance may cause operation - Water inlet pressure must be between 50 and 300 kPa, inconveniences and failures. otherwise install a pressure regulator on the line before the The most common problems are the following: appliance. - Install a cut-off valve for each supply on the line before PAN DOES NOT REACH SET TEMPERATURE: the appliance. - Make connections according to regulations currently in Possible causes: - Check connections to the switch. - Check connection to the working thermostat. - Check connection to electromagnetic switch. COMMISSIONING AND TESTING - Once all the connections have been made, the appliance - Heating elements are burned. and the overall installation must be checked following the SIGNAL LAMPS DO NOT LIGHT UP directions given in this manual. - Check in particular: - that the protective film has been removed from the exter- - Check the connection to the switch. nal surfaces; - that the terminal board housing, removed for electrical THE BRATT PAN WORKS connections, has been reinstalled. - that connections have been made in accordance with WITH DISCONNECTED THEMOSTAT the requirements and directions indicated in this manual; - that all safety requirements in current standards, statu- - Electromagnetic switch contacts are cut off. tory regulations and directives have been met; LOW EFFICIENTY OF THE PAN - that the water connections are leak-free; - that the electrical connection has been performed accor- Check the heating elements. ding to standards. CONNECTION TO WATERWORKS 006- 03 - Electric tilting cooker 6 Validity from serial number 70500783 USE AND CLEANING WARNINGS AND HINTS FOR USER - This manual contains all the instructions required for a proper and safe use of our appliances. Keep the manual in a safe place for future consultation!- This appliance is for catering use, hence they must be used only by trained kitchen staff. - The appliance must always be kept under control during use. Never use unmilled sea-salt with this appliance. It nevery fully dissolves but forms a layer of deposit on the bottom of the pan which can cause rust to form. Dissolve the salt in water separately before using. INSTRUCTIONS FOR USE - Before cooking with the appliance for the first time wash the interior of the cooking vat thoroughly. Warning!: Fill the cooking vat up to a maximum of 40 mm under the overflow border, according to the maximum level mark, including the food to be cooked. CLEANING AND CARE OF THE APPLIANCE - Do not use aggressive substances or abrasive detergents when cleaning the stainless steel components. - Avoid using metal pads of the steel parts as they may cause rust. [. . . ] - Remove the central heating element and then the fixing bulb boss (Pos. - Replacing the new thermostat be careful about tightening of the boss on the bulbs. If the bulbs would be squeezed, this would cause the damage of thermostat. HOW TO PROCEED, IF … Maintenance operations and repairs must be performed only by specialists! REPLACEMENT OF THE SWITCH Disconnect the appliance. After having removed the con- - Disconnect the power cables, after having removed the trol knob, remove the control panel, the handle of water in- front panel. [. . . ]