User manual WHIRLPOOL AGB 526/WP INSTRUCTION FOR USE

[. . . ] THE APPLIANCE MUST BE INSTALLED BY QUALIFIED PERSONNEL. Model AGB 600/WP AGB 526/WP Dim. : LxWxH 400 x 655 x 300 (550) 400 x 700 x 300 (320) 400 x 700 x 875 (1250) Voltage rating 230 V 230 V 230 V Power 1. 0 kW 1. 0 kW 1. 0 kW Lead wire / Section 3 x 1. 5 mm2 3 x 1 mm2 3 x 1. 5 mm2 A Luminous switch A A AGB 600/WP AGB 526/WP A 022- 03 - Electric chips scuttle 3 INSTALLATION INSTRUCTIONS Operating instructions Before beginning installation, remove all packaging from the appliance. Some parts are protected with an adhesive film which should be carefully removed. Any remnants of glue should be thoroughly cleaned using suitable substances such as benzine. [. . . ] Before starting to clean the appliance, disconnect from the mains. All steel parts should be washed in warm water, using a neutral detergent. Avoid using abrasive or corrosive detergents which could damage the steel. If stainless steel wool must be used, rub with and not against the satin finish. Never use ferrous materials which could cause rust to form. Legal and technical requisites When installing the appliance, the following safety standards must be adhered to: - Local accident prevention standards - Current CEI standards. Installation Installation, start-up and maintenance should only be carried out by expert personnel. All work required to install the appliance should be carried out in compliance with all local standards and regulations. The manufacturers decline all responsibility where poor performance is due to incorrect installation in disregard of the above conditions. What to do if not using the appliance for a long time Thoroughly clean and dry the machine as described. Disconnect the power supply. Warning! In compliance with international regulations, when connecting the appliance to the mains power supply, a device with a minimum aperture of 3 mm between contacts must be fitted upstream of the appliance, allowing omnipolar disconnection of the appliance from the mains. What to do if something goes wrong If anything goes wrong, immediately turn the appliance off, then turn off the power supply at the switch located upstream of the appliance, and call the aftersales department. Wiring When choosing the lead wire, make sure it has the following characteristics: it should be at least of the H07 RN-F type and its section should be large enough for the appliance (see "Technical specifications and dimensions", page 3). Cable entry is to the left, on the back. The terminal board is at the front, behind the control panel. Pass the wire through the core hitch and wire clamp, plug the leads into their terminals on the board and secure them. The earth lead must be a little longer than the others so that it is the last lead to disconnect if the wire clamp breaks. MAINTENANCE All maintenance should be carried out by qualified personnel only. Before carrying out any maintenance work, unplug the appliance or turn off the switch upstream of the appliance. Unipotential The appliance must be connected up to a unipotential system. The connecting screw is to be found to the right, on the back. [. . . ] Suitable separated collection so that the unit no longer used can be sent off for environmentally compatible recycling, treatment and disposal helps avoid possible negative effects on the environment and on health and facilitates the recycling of the product's component materials. For more detailed information on available collection systems, contact the local waste disposal service or the shop you purchased the unit from. Producers and importers fulfil their responsibility for environmentally compatible recycling, treatment and disposal both directly and by joining a collective scheme. 022- 03 - Electric chips scuttle 5 Wiring diagram R1 R2 B1 mA 1 2 3 L1 N PE 230V AGB 526/WP AGB 600/WP mA B1 R1 R2 Terminal boarc Main switch (green light) Resistances Resistances 022- 03 - Electric chips scuttle 6 WARNING THE MANUFACTURER CANNOT BE HELD RESPONSIBLE FOR ANY INACCURACIES IN THIS BOOKLET DUE TO COPYING OR PRINTING ERRORS. [. . . ]