User manual WHIRLPOOL AGB 532/WP INSTRUCTION FOR USE

[. . . ] THE APPLIANCE MUST BE INSTALLED BY QUALIFIED PERSONNEL. 3 - TECHNICAL DATA Model AGB 591/EP AGB 531/WP Dim. : LxWxH 400 x 615 x 300 400 x 700 x 300 400 x 700 x 875 800 x 615 x 300 AGB 532/WP 800 x 700 x 300 800 x 700 x 875 Voltage rating 230 V 230 V 230 V 230 V 230 V 230 V Power 1. 0 kW 1. 0 kW 1. 0 kW 2. 0 kW 2. 0 kW 2. 0 kW Lead wire / Section 3 x 1. 5 mm2 3 x 1. 5 mm2 3 x 1. 5 mm2 3 x 2. 5 mm2 3 x 2. 5 mm2 3 x 2. 5 mm2 003- 03 - Electric bain-marie 6 INSTALLATION INSTRUCTIONS Before beginning installation, remove all packaging from the appliance. Some parts are protected with an adhesive film which should be carefully removed. Any remnants of glue should be thoroughly cleaned using suitable substances such as benzine. [. . . ] The earth lead must be a little longerthan the others so that it is the last lead to disconnect if the wire clamp breaks. Unipotential The appliance must be connected up to a unipotential system. The connection screw is located on all top models at the back on the right hand side, while in other models it is located underneath the appliance on the right hand side. It is labelled. Warning! With Top models, carefully measure the distance between the appliance and the edge of the base (Fig. Legal and technical requisites When installing the appliance, the following safety standards must be adhered to: The manufacturers cannot be held responsible for any damage due to inadequate or incorrect installation. Under such circumstances the guarantee will be considered null and void. - Local accident prevention standards - Current CEI standards. Warning! - Beware of inexpert handling!- Never leave the appliance on without water! Ignition Installation Installation, start-up and maintenance should only be carried out by expert personnel. All work required to install the appliance should be carried out in compliance with all local standards and regulations. The manufacturers decline all responsibility where poor performance is due to incorrect installation in disregard of the above conditions. Check that the water drain release is closed. Fill the bath with water up to the level marked. Turn on the main switch upstream of the appliance. On the twin-bath models (AGB 532/WP) both baths can be used independently of each other at different temperatures, or one can be used without the other. It will light up indicating that the appliance is on. Switch on switch C (pages 4 . . . 5) and use knob A to position the thermostat on the desidered temperature, between 30°C and 90°C inclusive; the pilot light will come on; this means that the resistances are on. As soon as the required temperature is reached, the pilot light will go off. To turn the appliance off, simply turn the knob back to '0' and switch off. Warning! In compliance with international regulations, when connecting the appliance to the mains power supply, a device with a minimum aperture of 3 mm between contacts must be fitted upstream of the appliance, allowing omnipolar disconnection of the appliance from the mains. 003- 03 - Electric bain-marie 7 USING THE APPLIANCE Emptying the bath First of all a suitable bowl for emptying the water into should be found. Fit the drainage pipe as shown in the THE 2002/96/EC DIRECTIVE (WEEE): information to users This informational note is meant only for owners of equipment marked with the symbol shown in Fig. A on the adhesive label featuring the technical specifications applied on the actual product (the label also giving the serial number). [. . . ] All steel parts should be washed in warm water, using a neutral detergent, then rinsed thoroughly to eliminate any residual detergent. Avoid using abrasive or corrosive detergents which could damage the steel. What to do if not using the appliance for a long time Thoroughly clean and dry the machine as described. Disconnect the power supply. What to do if something goes wrong If anything goes wrong, immediately turn the appliance off, then turn off the power supply at the switch located upstream of the appliance, and call the aftersales department. MAINTENANCE All maintenance should be carried out by qualified personnel only. [. . . ]