User manual WHIRLPOOL AKM 213/IX/01 PROGRAM CHART

[. . . ] This cooking hob has been designed, constructed and marketed in compliance with: - safety requirements of EEC Directive “Gas” 90/396; - safety requirements of EEC Directive “Low voltage” 73/23; - protection requirements of EEC Directive “EMC” 89/336; - requirements of EEC Directive 93/68. n 13 M Y N C ENERGY SAVING TIPS x x The cooking hob is equipped with burners and/ or a hotplate having different diameters. Use pots and pans whose bottom diameter is equal to that of the burners and hotplate, or slightly larger. Burner Large (9, 1 cm) Medium (6, 4 cm) Small (4, 5 cm) Double crown (12 cm) Fish kettle (23 cm x 4, 5 cm) Diameter of container 24 16 8 24 to to to to 26 22 14 26 cm cm cm cm x A pressure cooker allows you to save even more energy and time. 16x35 cm x x If possible, keep the pot covered when cooking. with little water in order to cut down cooking time. CLEANING AND MAINTENANCE Cleaning the cooking hob surface and panstand grids x x x x Before cleaning the cooking hob, disconnect it from mains power supply and wait until it has cooled down. [. . . ] Wipe with a cloth moistened with water and salt, and polish with a cloth moistened with oil. M Y N C TROUBLE-SHOOTING GUIDE 1. The burner fails to ignite: y Is the main gas delivery valve open?y Has the delivery of the town gas (methane) been suspended?y Is the gas cylinder (liquid gas) empty?y Have the cap and burner been positioned correctly after cleaning?(See paragraph “Cleaning and Maintenance”. ) 2. The burner fails to remain lit: y Repeat the ignition operation, turning the knob to the position with the small flame symbol . The electric ignition device does not work: y Is there a power failure? AFTER-SALES SERVICE Before you call the After-Sales Service: 1. Carefully check the “Troubleshooting guide” above to see if you can fix the problem yourself. Re-start the cooking hob, to check whether correct operation has been restored. If the malfunction persists, call the After-sales Service. Important: if a stainless steel hose is used, it must be installed so as not to touch any movable part of the furniture. It must pass through an area where there are no obstructions and where it is possible to inspect it on all its length. b a b Connection and installation Oven and cooking hob with universal joints After having installed and fixed the cooking hob, install the oven. Connect tongues to end , as shown in the figure. If the cooking hob is equipped with an electric to the first hotplate, connect 3-plug assembly 3 bores of the 5-pole terminal board on block , as shown in the figure. Position the oven and fix it with the screws supplied. Fit the knobs, pressing them into their seats on the control panel. a b a b r a r a a r Note If the cooking hob must be connected to the Box instead of the oven, read the instructions supplied with the Box. Slacken off the screws and position the cooktop in such a way that the taps are aligned with the oven knobs. Adjust the height of the taps bracket according to the position (2, 3, 4, 5) indicated on the brackets . Once adjusted to the correct height, tighten the screws . Use the screws provided to secure the to the oven panel. cooktop taps bracket Fit the knobs. a d c c a b 18 M Y N C INSTALLATION Adjustment to different types of gas If a different type of gas from the one indicated in the plate is used, the cooking hob must be adapted to it. [. . . ] Re-assemble the injector in . a b c c a b d d Adjusting minimum gas setting of taps To ensure that the minimum setting is correctly adjusted, remove knob and proceed as follows: x tighten (-) to reduce the height of the flame; x loosen (+) to increase the height of the flame. The adjustment must be performed with the tap in minimum gas setting position (small flame) . 19 M Y N C NATIONAL SAFETY REGULATIONS ITALY Ventilation of room When the appliance is not equipped with safety devices on the burners (thermocouples), the air vents must be increased by 100%, and must be at least 200 cm2, in compliance with the departmental decree of 21 April 1993. Gas supply system Before connecting the appliance, make sure that the gas supply system complies with standards UNI 7129 and UNI 7131. Connection to gas supply The connection to the gas pipe network or gas cylinder must be made with a rigid copper or steel pipe with fittings complying with standards UNI 7129, or with a continuoussurface stainless steel hose complying with standards UNI 9891. [. . . ]