User manual WHIRLPOOL AKM 394/IR INSTRUCTION FOR USE

[. . . ] When replacing the grids, make sure that the panstand area is aligned with the burner and that the burner feet are fitted in the respective housings on the hob surface. In the case of single grids, make sure that they fit on the burner cap protuberance. Models equipped with electrical ignition plugs and safety device require thorough cleaning of the plug end in order to ensure correct operation. Check these items frequently, and if necessary, clean them with a damp cloth. [. . . ] In this case, repeat the operations described above. Safety device is optional - if Your model is not equipped with it, the • Ensure that the installation and gas/electrical connections are performed by a qualified technician in ignition should be instant. compliance with current local safety regulations. • This appliance must only be installed and used in well-ventilated rooms, in accordance with current If Your model is equipped with cast iron electric hotplate You can easy operate it with relevant knob. Read instructions before installing and using this appliance. By turning the knob from position 1 to 6 You can increase the temperature. Switch off the hotplate by turning knob to 0 • Gas adjustment and supply pressure are indicated on the rating plate located under the hob. If the appliance is arranged for a type of gas different from that available, refer to the paragraph “Adjustment to different types of gas”. Manufacturer: Whirlpool Europe S. r. l. Borghi, 27 21025 Comerio (VA) ITALY 5019 619 01387/B NOTES: • • Improper use of the grids can result in damage to the hob surface. Do not position the grids upside down or drag them across the hob. If the hob has a glass ceramic top, do not use: - Cast iron griddles or terracotta pots and pans - Heat diffusers (e. g. Disposal must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Declaration of conformity • This hob has been designed, constructed and marketed in compliance with: - safety requirements of “Gas” Directive 2009/142/EC (ex: EEC 90/396); - safety objectives of the “Low Voltage” Directive 2006/95/CE (which replaces 73/23/CEE and subsequent amendments); - protection requirements of EEC Directive “EMC” 2004/108. • This cooktop is suitable for contact with foodstuffs and complies with EEC (CE) Regulation n. 1935/2004. Before calling the After-Sales Service, make sure you can give the following information: type of fault or problem; exact model (written on the Instruction and Warranty); service number that follows the word SERVICE on the rating plate under the hob and on the Warranty; your complete address and phone number. REFERENCE TO LOCAL REGULATIONS Installation must be performed in accordance with standard NBN D 51-003. INSTALLATION TECHNICAL INFORMATION FOR THE INSTALLER • • This product can be embedded in a worktop 20 to 40 mm thick. If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the work surface. This panel must be positioned at a maximum distance of 150 mm below the upper surface of the work surface but, in no case less than 20 mm from the bottom of the hob. In the case that you intend to install an oven beneath the hob, make sure that it is manufactured by Whirlpool and equipped with a cooling system. The manufacturer declines all liability if another brand oven is installed beneath the hob. Before installation, make sure that: the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see the rating plate and injector table). The outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations. [. . . ] Attention: if a stainless steel hose is used, it must be installed so as not to touch any mobile part of the furniture. Connect tongues (A) to ending (B) as shown in the figure. It must pass through an area where there are no obstructions and where it is possible to inspect it on all its length. If your hob is equipped with an electric hotplate, connect 3plug assembly (R) to the first 3 bores of the 5 pole terminal • After connection to the gas supply, check for leaks with soapy water. [. . . ]