User manual WHIRLPOOL AKM 900/NE/02 PROGRAM CHART

[. . . ] Do not leave the hot plates/cookers turned on when they are empty. Do not rest plastic, aluminium foil, cloths, paper etc. The hob is fitted with hot plates/cookers of different sizes. Use pans whose bottom diameter is equal to that of the hot plates/cookers, or slightly larger. BEFORE USING THE COOKING HOB Before use, remove: - adhesives stuck on the hob; - cardboard guards and protective plastic film; - check whether the hob has been damaged during transport. [. . . ] Do not allow children to touch: - the hob in general, to avoid burns. During and immediately after use the hob reaches extremely high temperatures; - packing materials (bags, polystyrene, metal parts, etc. ); - the hob to be scrapped. Make sure that the electrical wires of other electrical appliances near the hob do not come into contact with hot parts of the hob itself. DIMENSIONS OF THE COOKING HOB AND WORKTOP (mm) Make sure that the voltage indicated on the rating plate is the same as the mains voltage. Technical data is given on the rating plate on the edge of the hob and also below: ELECTRICAL CONNECTION Supply voltage 230 V ~ 230 V 3 ~ + 400 V 3N ~ + 400 V 2N ~ + Conductors (number and size) 3 X 2. 5 mm2 4 X 1. 5 mm2 5 X 1. 5 mm2 4 X 1. 5 mm2 CAUTION • • • Telescopic knobs (depending on model) • • The knobs can be lifted approx. After cleaning, restore the knob to its original position. - Make sure that the power supply is on. - Turn the hob off and on again, to make sure that the problem has been solved. - Make sure that the knob is not turned to “0”. Turn the multi-pole switch to “Off” for a few minutes and then turn it back to “On”. TROUBLESHOOTING GUIDE The hob does not work: • • • • The hob will not switch off: - disconnect the hob immediately from the power supply. • Type PLEVS 230 V~/400 V 3 N~ 50 Hz 6, 5 kW 5019 319 54391/A To get full satisfaction from the hob, please read these instructions carefully and keep them for future consultation. Whirlpool is a registered trademark of Whirlpool USA AFTER SALES SERVICE Before you call the After Sales Service • Make sure that you cannot solve the problem yourself following the points described in chapter “Troubleshooting Guide“. If after the above checks the fault still occurs, get in touch with the nearest After Sales Service. Please give: • a short description of the fault; • the exact type and model of hob; service number (i. e. , the number that follows the word SERVICE on the rating plate under the hob itself). The service number is also indicated on the guarantee booklet; • your full address; • your telephone number. If any repairs are required, please contact an authorised After Sales Service (to guarantee that original spare parts will be used and repairs carried out correctly). Failure to comply with these instructions may compromise the safety and quality of the product. • Declaration of conformity • • This hob is suitable for contact with foodstuffs, and complies with EEC Directive 89/109. This hob (Class Y) has been designed to be used only for cooking. Any other use (such as heating a room) is improper and dangerous. • This hob has been designed, constructed and marketed in compliance with: - safety requirements of EEC Directive “Low voltage” 73/23; - protection requirements of EEC Directive “EMC” 89/336; - requirements of EEC Directive 93/68. The Manufacturer reserves the right to change product specifications without prior notice. INSTALLATION Recommendations Important: Disconnect the hob from the mains before carrying out any installation work or servicing. • All electrical connections must be made before connecting the appliance to the power supply. • Installation must be carried out by a qualified technician in accordance with the manufacturer's instructions and in compliance with local regulations. • Unpack the hob and make sure that the appliance has not been damaged during transport. If you are not sure contact the dealer or the nearest service centre. 3. Preparing the housing unit Cut the worktop to fit before installing the appliance. [. . . ] 1 Electrical connection • • • • • • • Fig. 3 Connecting the oven to the power supply Note: the yellow/green earth wire must be connected to the screw with the symbol . 70 mm of the cable sheath from the power supply cable (G). Insert the cable (G) through the opening in the lid (F). [. . . ]