User manual WHIRLPOOL AKM227/IX INSTRUCTION FOR USE

[. . . ] When replacing the grids, make sure that the panstand area is aligned with the burner and that the burner feet are fitted in the respective housings on the hob surface. In the case of single grids, make sure that they fit on the burner cap protuberance. Models equipped with electrical ignition plugs and safety device require thorough cleaning of the plug end in order to ensure correct operation. Check these items frequently, and if necessary, clean them with a damp cloth. [. . . ] Safety device is optional - if Your model is not equipped with it, the • Ensure that the installation and gas/electrical connections are performed by a qualified technician in ignition should be instant. compliance with current local safety regulations. • This appliance must only be installed and used in well-ventilated rooms, in accordance with current If Your model is equipped with cast iron electric hotplate You can easy operate it with relevant knob. Read instructions before installing and using this appliance. By turning the knob from position 1 to 6 You can increase the temperature. Switch off the hotplate by turning knob to 0. • Gas adjustment and supply pressure are indicated on the rating plate located under the hob. If the appliance is arranged for a type of gas different from that available, refer to the paragraph “Adjustment to different types of gas”. Manufacturer: Whirlpool Europe S. r. l. Borghi, 27 21025 Comerio (VA) ITALY 5019 619 01200 NOTES: Improper use of the grids can result in damage to the hob surface. Do not position the grids upside down or drag them across the hob. • If the hob has a glass ceramic top, do not use: - Cast iron griddles or terracotta pots and pans - Heat diffusers (e. g. The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Declaration of conformity • This hob has been designed, constructed and marketed in compliance with: - safety requirements of EEC Directive “Gas” 90/396 - safety objectives of the “Low Voltage” Directive 2006/95/CE (which replaces 73/23/CEE and subsequent amendments); - protection requirements of EEC Directive “EMC” 89/336 - requirements of EEC Directive 93/68 • This cooktop is suitable for contact with foodstuffs and complies with EEC (CE) Regulation n. 1935/2004. Before calling the After-Sales Service, make sure you can give the following information: type of fault or problem; exact model (written on the Instruction and Warranty); service number that follows the word SERVICE on the rating plate under the hob and on the Warranty; your complete address and phone number. REFERENCE TO LOCAL REGULATIONS Provision for ventilation The room in which the appliance is installed must have an air supply to current B. S. All rooms require a permanent vent in addition to the openable window. If there are other fuel burning appliances in the same room B. S. 5440 - Part 2 should be consulted to determine the air vent requirements. If the appliance is installed in a cellar or basement, it is advisable to provide an air vent of 65 cm, irrespective of the room volume. INSTALLATION TECHNICAL INFORMATION FOR THE INSTALLER • • This product can be embedded in a worktop 20 to 40 mm thick. If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the work surface. [. . . ] You can find specific local regulations for some countries in the paragraph “Reference to Local Regulations”. If no information concerning your Country is given, please ask details to your Installer. The connection of the hob to the gas pipe network or gas cylinder must be made by means of a rigid copper or steel pipe with fittings complying with local regulations, or by means of a continuous-surface stainless steel hose complying with local regulations. The maximum length of the hose is 2 linear metres. [. . . ]