User manual WHIRLPOOL AKR 002/IX INSTRUCTION FOR USE

[. . . ] N C INTRODUCTION BEFORE USING THE COOKTOP 1. Light the burners to remove fumes and smells from the protective greases. Turn the control knob to the “large flame” position 2. Operate the electric ignition (see the model specifications) 3. [. . . ] Keep children away. 35 M 35 Y N C CLEANING AND MAINTENANCE CLEANING THE COOKTOP AND CONTROL PANEL x x x x CLEANING THE BURNERS AND THE GRIDS x x Before cleaning the cooktop switch it off and wait for it to cool down. Clean with a cloth wetted with hot water and soap or water and liquid detergent. Do not use products which are abrasive, corrosive or chlorine based, or steel pads. Do not leave acid or alkaline substances (vinegar, salt, lemon juice etc. ) on the cooktop. x x ENAMEL COOKTOP x Enamelled parts must be washed using a sponge, with soapy water or other non-abrasive products. If acid substances such as lemon juice, tomato conserve, vinegar etc. are left on the enamel for a long time they will etch it, making it opaque. x These pieces can be removed and washed with suitable products. After cleaning, the burners and spreaders must be dried carefully and put back into their housing correctly. It is very important to check the correct position of the burner spreader because if it moves out of place serious problems could occur. In models which have safety valves, make sure that the sensor, near to each burner, remains clean so that the safety valves can work properly. In appliances with electric ignition make sure that the electrode remains clean so that the sparks can strike properly. The spark plugs must be cleaned very carefully. N. B. : To avoid damage to the electric ignition, do not use it when the burners are not in place. STAINLESS STEEL COOKTOP x x x Stainless steel parts must be rinsed with water and dried with a soft and clean cloth or with a chamois leather. For difficult dirt, use a specific non-abrasive product available commercially or a little hot vinegar. Note: regular use could cause discolouring around the burners, because of the high temperature. GAS TAPS The gas taps should be cleaned regularly and only by specialised engineers. If the gas taps are not working correctly, call the AfterSales Service. 36 M 36 Y N C TROUBLE-SHOOTING GUIDE 1. The burner does not light: x Is the gas supply tap switched on?x Has the gas supply (methane) been cut off?x Have the cap or burner been repositioned correctly after cleaning?The burner does not stay lit: x Repeat the lighting operation turning the knob to the symbol representing the small flame . = 3. The electric ignition does not work: x Is there a power failure? AFTER-SALES SERVICE Before contacting the After-Sales Service: 1. Check whether you can deal with the problem yourself (See “Trouble Shooting Guide”). Switch on the appliance again to check whether the problem has been solved. If it is still not working properly, call the After-Sales Service. [. . . ] The burners are so designed that there is no need to adjust the primary air. 44 M 44 Y N C INSTALLATION o BURNERS Medium-power High-power Rated output [kW] 1, 650 3, 000 INJECTOR TABLES cat. III 1a2H3+ Low output [kW] 0, 35 0, 60 G30/G31 28-30/37 mbar Ø injector [1/100 mm] 65 85 G20 20 mbar Ø injector [1/100 mm] 94 128 G110 8 mbar Ø injector [1/100 mm] 185 290 kvo BURNERS Medium-power High-power Double-crown Rated output [kW] 1, 650 3, 000 3, 300 Low output [kW] 0, 35 0, 60 1, 50 cat. II 2H3+ G30/G31 28-30/37 mbar Ø injector [1/100 mm] 65 85 92 G20 20 mbar Ø injector [1/100 mm] 94 128 139 l BURNERS Medium-power High-power Rated output [kW] 1, 650 3, 000 Low output [kW] 0, 35 0, 60 cat. II 2E+ 3+ G30/G31 28-30/37 mbar Ø injector [1/100 mm] 65 85 G20/G25 20/25 mbar Ø injector [1/100 mm] 94 128 m BURNERS Medium-power High-power Rated output [kW] 1, 650 3, 000 Low output [kW] 0, 52 0, 85 G20 20 mbar Ø injector [1/100 mm] 94 128 cat. [. . . ]