User manual WHIRLPOOL AKR 948 IX PROGRAM CHART

[. . . ] Rökröret och rörklämmorna (15) som krävs för installationen levereras inte tillsammans med fläktkåpan, utan måste köpas separat. N INSTALLASJONSVEILEDNING Minimumsavstand til komfyrtopp: 50 cm (elektriske kokeplater), 75 cm (gass-, parafin- eller kullkomfyr). Følg nummereringen ved montering (1Ö2Ö3Ö. . . . . ). Apparatet må ikke tilkobles strømnettet før installasjonen er helt avsluttet. Avtrekksrøret og festebåndene (15) følger ikke med og må anskaffes separat. DK INSTALLATIONSVEJLEDNING Minimumafstand fra kogezoner: 50 cm (elkogezoner), 75 cm (gas-, olie- eller kulfyrede kogezoner). [. . . ] Carry out the electrical connections between the two parts. Fix the hood to the extraction unit with 10 screws. Using a pencil, draw the centre line on the wall up to the ceiling to facilitate installation operations. Attach the hole diagram to the wall: the vertical centre line printed on the hole diagram must match the centre line drawn on the wall, and the lower edge of the hole diagram must match the lower edge of the hood: remember that with installation completed the bottom of the hood must be at least 50 cm above the cooktop in case of electric cookers and 75 cm in case of gas or mixed cookers. Place the support bracket on the hole diagram so that it matches the dashed rectangle, mark the two external holes and drill, remove the hole diagram, insert 2 wall plugs and fix the hood support bracket with two 5x45 mm screws. Adjust the distance between the hood and the wall. From inside the hood, mark the holes for fixing the hood permanently. Drill on the marks (Ø 8 mm - see step 10). Fit the flue support bracket G to the wall and against the ceiling, use the support bracket as hole diagram (the small slot on the support must match the line drawn on the wall - step 4) and mark 2 holes with the pencil, drill the holes (Ø 8 mm), and finally insert 2 plugs. Fix the flue support bracket to the wall with two 5x45 mm screws. Fix the hood to the wall with two 5x45 mm screws (ABSOLUTELY NECESSARY). Connect an exhaust pipe (pipe and clamps are not supplied and must be bought separately) to the collar B located above the extraction motor unit. For extractor operation, connect the other end of the exhaust pipe to the home discharge device. For filter operation, fix the deflector F to the flue support bracket G with 2 screws and connect the other end of the exhaust pipe to the deflector collar F (if the collar is not already fitted it should be inserted on the deflector and secured with 1 screw). Once the steam and fumes have been filtered by the carbon filter (not provided, to be ordered separately) they are conveyed back to the kitchen through grid H. Apply the flues and fix them with 2 screws (20a) to the flue support G (20b). Slide the bottom section of the flue in the special seat above the hood to completely cover the extraction unit. Refit the grease filter/s and check for correct hood operation.  5019 318 33080 S N DK FIN GB 31833080. fm Page 12 Friday, June 6, 2003 3:45 PM AKR 948 1. Telescopic flue. PRODUCT SHEET CONTROL PANEL To clean the grease filter Wash the grease filter at least once a month. 1: pull the spring release handle (f) downwards, then remove the filter. [. . . ] After washing, dry the filter in the oven at 100° C for 10 minutes to reactivate it. The filter will retain its odour-absorbing capacity for three years, after which it must be replaced. Fig. Use a small screwdriver or any other suitable tool to prise off (m-Fig. Replace using 20 W max halogen bulbs only, making sure not to touch them with your hands. [. . . ]