User manual WHIRLPOOL AKR 963 IX INSTRUCTION FOR USE

[. . . ] Cut an opening in the worktop of the dimensions shown in the Product Description Sheet supplied separately. If not already present, fit the supplied seal to the cooktop flange after cleaning the contact area as shown in the figure. If the worktop is made of wood, fit the supplied clips. • • • Cooktop with electric hotplates • 1. Position the 4 spring clips (G) and fit them in their locations on the underside of the cooktop. [. . . ] After the appliances have been installed, the electrical components must be inaccessible. • • • • Interconnecting control box and cooktop • Make sure that the voltage shown on the rating plate is the same as the power supply voltage in your home. The rating plate is on the control box and on the product description sheet. Use a type H05RR-F power cord (minimum length 800 mm). Remove cover (P) and connect the supply cord to the junction block following the indications given in the table. Attention: The control box is pre-set in the Factory for connection 1. For any other connection, please refer to the table here under. Supply voltage 1 230 V 1N ~ + Conductors: Number and size 3 X 2, 5 mm² Electrical connection • • • 2 230 V 3 ~ + 4 X 1, 5 mm² 3 400 V 2N ~ + 4 X 1, 5 mm² • • Connect the 3 pole and 4 pole connectors to the respective connectors on the control box. The 3 pole connectors (Q) is located at the rear right hand side of the control box, the 4 pole connector (R) is located at the left hand side of the control box (see-figure). Connect the yellow/green striped earth wire ( ) (S) from the cooktop to the screw located near the 3 pole connector (T). WARNING: DO NOT CONNECT TO THE POWER SUPPLY BEFORE YOU HAVE FINISHED CONNECTING THE CONTROL BOX AND COOKTOP. • Mount the control box in the kitchen unit. Make sure the power cord is not entrapped. 88 BEFORE USING THE COOKTOPS To make the most of your new appliances, read the users instructions carefully and keep them on hand for consultation in the future. for room heating) is considered as improper use and potentially dangerous. The appliances are designed, built and sold in compliance with: The safety requirements of “Low Voltage” Directive 73/23/EEC. The protection requirements of EMC Directive 89/336/EEC. This appliance complies with Class “Y” fire protection category. • • • • • • Conventional electric / glass-ceramic cooktop • • Do not switch on the hotplates/cooking zones when there is no pan in position. The cooktop features different size hotplates/ cooking zones. Use pans whose base diameter is the same as or slightly larger than the diameter of the hotplate/cooking zone. The use of pans with concave or convex bottoms may damage the cooktop. Do not use the cooktop as a worksurface or a support surface. Do not leave the appliance unattended when frying food -risk of fire. Declaration of conformity CE • • • • • • • • • 90 COOKTOP ACCESSORIES Child guard accessory KBL 2 (for cooktops 600 mm only) This accessory can be obtained from the After Sales Service under Part N° 4819 310 18436. . MAINTENANCE AND CLEANING OF CONVENTIONAL ELECTRIC COOKTOPS Before cleaning the cooktop, disconnect it from the electrical supply and wait until it has cooled. Care and Maintenance of conventional cooktop • Use a cloth and warm soapy water. • Do not use abrasives, corrosive cleaners, cleaners containing chlorine or pan scourers. [. . . ] • Remove baked-on dirt with the supplied scraper tool and specific cleaning products. • Food spills should be cleaned off before they bake onto the glass-ceramic surface. • Do not use abrasive products, bleach, ovencleaner spray or pan scourers. • The cooktop should be treated periodically with a proprietary brand of protective wax for glass-ceramic hobs. 91 TROUBLESHOOTING GUIDE Cooktop not working • Ensure that the cooktop is receiving electrical power. [. . . ]