User manual WHIRLPOOL AKS 370/IX INSTALLATION

[. . . ] Do not leave acid or alkaline substances, such as vinegar, mustard, salt, sugar or lemon juice on the hob. Symbols Shaded circle Large flame Small flame Star Tap closed Maximum opening/delivery Minimum opening or reduced delivery Electric ignition • • • • CLEANING THE HOB PARTS The symbols are indicating which cooking field this knob activates Note: Your cooktop aesthetics can be slightly different from the drawing. • • • • • • Grids, burner caps and burners can be removed to be cleaned. Clean them by hand with warm water and non-abrasive detergent, removing any food residues and checking that none of the burner openings is clogged. Rinse and dry Refit burners and burner caps correctly in the respective housings. [. . . ] metallic mesh) - Two cookers for the same pot • In case of prolonged use, additional ventilation may be needed (opening a window or increasing the extraction force of the hood). • This appliance is not intended for use by people (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given initial supervision or instruction concerning use of the appliance by a person responsible for their safety. • Keep children away from the hob when it is in use and do not let them play with the controls or any other appliance parts. Warning: the protective rubber feet on the grids could represent a chocking hazard for young children. After removing the grids, please ensure that all the feet are correctly fitted. Warning: the glass lid (if provided) may shatter if overheated. Before closing it, be sure that all the burners are off. After use, make sure that the knobs are in position OFF and close the main gas delivery or cylinder tap • TROUBLESHOOTING GUIDE If the hob will not operate correctly. Before calling the After-Sales Service, refer to the Troubleshooting Guide to determine the problem. 1. • • • • • • 2. The burner fails to ignite or the flame is not even Check that: The gas or electrical supplies are not shut off and especially that the gas supply tap is open. The gas cylinder (liquid gas) is not empty. All the burner parts have been positioned correctly. The burner does not stay lit Check that: When lighting the burner, the knob has been pressed for enough time to activate the protection device. The burner openings are not clogged near the thermocouple. The end of the safety device is not dirty. The minimum gas setting is correct (see relevant paragraph). The containers are not stable Check that: The bottom of the container is perfectly flat The container is centered on the burner. The grids have not been exchanged or positioned incorrectly. • • • • 3. • • • If after the above checks the fault still occurs, get in touch with the nearest After Sales Service. AFTER-SALES SERVICE PROTECTING THE ENVIRONMENT 1. Packaging The packaging material is entirely recyclable, and is marked with the recycling symbol , which identifies it as a type of material that must be sent to local waste-disposal centres. If any repairs are required, please contact an authorised After-Sales Service, as indicated in the warranty. Product This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). Note: Failure to comply with these instructions may compromise the safety and quality of the product. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. [. . . ] Earth • If you have a Triple Crown burner use side spanner to (yellow/green) replace the injector (E) Before installing the hob, remember to affix the gas N calibration plate supplied with the injectors in such a way • The manufacturer cannot be held responsible for any injury to persons or animals or damage to property that it covers the existing information relating to gas arising from failure to comply with these requirements. • When the hob is installed, provide a multi-pole circuit breaker with a contact separation of at least 3 mm. • If necessary, the electrical power cable must be replaced exclusively with a power cable having identical characteristics to the original supplied by the manufacturer (type H05V2V2-F T90°C or H05RR-F). This operation must be performed by a qualified electrician. ADJUSTING MINIMUM GAS SETTING OF TAPS To ensure that the minimum setting is correctly adjusted, remove the knob and proceed as follows: • tighten screw to reduce the flame height (-) • loosen screw to increase the flame height (+) The adjustment must be performed with the tap in minimum gas setting position (small flame) . [. . . ]