User manual WHIRLPOOL AKT 351/IX INSTRUCTION FOR USE

[. . . ] 25 PRATICAL ADVICE FOR USING THE BURNERS For optimum burner performance, observe the following rules: Use pots and pans that fit the burners (see table on the right). Use the correct amount of water for cooking foods and keep the pot covered. Burner 4 ring burner Pot Ø from 24 to 26 cm NATURAL GAS 4 ring (Methane) G20 LIQUEFIED 4 ring PETROLEUM GAS (Butane) G30 LIQUEFIED PETROLEUM GAS 4 ring (Propane) G31 Type of gas used Model configuration 1 burner 1 burner 1 burner 139 95 3. 50 254 g/h 1. 50 20 28-30 35 95 3. 50 250 g/h 1. 50 25 37 45 Rated thermal flow rate kW 3. 50 3. 50 3. 50 Total rated consumption 333 l/h 254 g/h 250 g/h Air necessary (m3) for the combustion of 1 m3 of gas 9. 52 30. 94 23. 8 G20 20 mbar G30 28-30 mbar G31 37 mbar ELECTRICAL SUPPLY: 230 V ~ 50 Hz 5019 319 01476 To get full satisfaction from the hob, please read these instructions carefully and keep them for future consultation. PRECAUTIONS AND GENERAL RECOMMENDATIONS To get full satisfaction from your hob, please read these instructions carefully and keep them for future consultation Declaration of conformity • This hob has been designed, constructed and marketed in compliance with: - safety requirements of EEC "Gas" Directive 90/396 - safety objectives of the “Low Voltage” Directive 2006/95/CE (which replaces 73/23/CEE and subsequent amendments). - protection requirements of EEC “EMC” Directive 89/336 - requirements of EEC Directive 93/68 This hob is suitable for contact with foodstuffs and complies with EEC (CE) Regulation n. [. . . ] Before installation, make sure that: the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see the rating plate and injector table). the outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations. combustion products are discharged outdoors through specific hoods or wall and/or window mounted electrical fans. continuous natural air circulation is ensured through a clear opening in a wall of at least 100 cm2. This wall opening must be: permanent and in a wall to the outside of the room to be vented; made in such a way that it cannot be obstructed from the inside or outside (not even accidentally); Protected by plastic grilles, metal mesh, etc. , which do not reduce the above-mentioned useful area; located near floor level and positioned so as not to interfere with the operation of the exhaust system. SAFEGUARDING THE ENVIRONMENT 1. Packaging The packaging material is entirely recyclable, and is marked with the recycling symbol , which identifies it as a type of material that must be sent to local waste-disposal centres. Product This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health. The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead, it must be delivered to an appropriate collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal. For further information on the treatment, recovery and recycling of this appliance, contact your competent local authority, the collection service for household waste or the shop where you purchased the appliance. • a) b) c) d) INSTALLATION GAS CONNECTION • • • The gas supply system must comply with local regulations. You can find specific local regulations for some countries in the paragraph “Reference to Local Regulations”. If no information concerning your Country is given, please ask details to your Installer. The connection of the hob to the gas pipe network or gas cylinder must be made by means of a rigid copper or steel pipe with fittings complying with local regulations, or by means of a continuous-surface stainless steel hose complying with local regulations. The maximum length of the hose is 2 linear metres. Before connecting the tube to the elbow fitting (A), interpose the washer (B) supplied, in compliance with EN 549. A fig. 4 • For setting into a marble worktop, contact the After-sales Service for the installation kit and necessary instructions. 4812 310 19277 Installation kit for marble worktop. Attention: if a stainless steel hose is used, it must be installed so as not to touch any mobile part of the furniture. [. . . ] Clean them by hand with warm water and non-abrasive detergent, carefully removing any food residues and checking that none of the burner openings is clogged. Refit burners and burner caps correctly in the respective housings. When replacing the grids, make sure that the panstand area is aligned with the burner and that the burner feet are fitted in the respective housings on the hob surface. In the case of single grids, make sure that they fit on the burner cap protuberance. [. . . ]