User manual WHIRLPOOL AKT 477/IX INSTALLATION

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual WHIRLPOOL AKT 477/IX. We hope that this WHIRLPOOL AKT 477/IX user guide will be useful to you.

Lastmanuals help download the user guide WHIRLPOOL AKT 477/IX.


Mode d'emploi WHIRLPOOL AKT 477/IX
Download

You may also download the following manuals related to this product:

   WHIRLPOOL AKT 477/IX PROGRAM CHART (805 ko)
   WHIRLPOOL AKT 477/IX INSTRUCTION FOR USE (927 ko)

Manual abstract: user guide WHIRLPOOL AKT 477/IXINSTALLATION

Detailed instructions for use are in the User's Guide.

[. . . ] IMPORTANT SAFETY INFORMATION Your safety and the safety of others are very important. This manual and the appliance itself provide important safety messages, to be read and observed at all times. This is the safety alert symbol, pertaining to safety, which alerts users to potential hazards to themselves and others. All safety messages will follow the safety alert symbol and either the terms: - Overheated oils and fats catch fire easily. [. . . ] • Before connecting the tube to the elbow fitting (A), interpose the washer (B) supplied, in compliance with EN 549. NOTE: if a stainless steel hose is used, it must be installed so as not to touch any mobile part of the furniture. It must pass through an area where there are no obstructions and where it is possible to inspect it on all its length. • After connection to the gas supply, checkfor leaks with soapy water. Electrical connections • Hob electrical connection must be made before connecting the appliance to the electricity supply. • Electrical connection must be carried out in compliance with the regulations of the local electric utility company. • Make sure that the voltage indicated on the rating plate on the underside of the appliance corresponds to the domestic power supply voltage. • Regulations require that the appliance is earthed: use conductors (including the earth conductor) of the appropriate size only. • For electrical connection, use an H05 RR-F type cable as specified in the table “Power supply voltage”. INSTALLATION AND FIXING The installer is responsible for any damage or injury resulting from incorrect installation. To guarantee correct operation, the appliance must be installed on a perfectly flat surface. If necessary, cut the kitchen unit and worktop to fit before installing the hob. Clean the cutout of any chips that could compromise appliance operation. Install a separating panel under the hob (no separation panel is needed in case of oven under the hob) • a) b) c) d) Before installation, make sure that: the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see the rating plate and injector table). The outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations. Combustion products are discharged outdoors through specific hoods or wall and/or window mounted electrical fans. Continuous natural air circulation is ensured through a clear opening in a wall of at least 100 cm2. This wall opening must be: permanent and in a wall to the outside of the room to be vented; made in such a way that it cannot be obstructed from the inside or outside (not even accidentally); protected by plastic grids, metallic mesh, etc. , taking care not to reduce the air vent effective area mentioned a bove; located near floor level and positioned so as not to interfere with the operation of the exhaust system Connecting to the terminal board Connect the yellow/green earth wire to the terminal with the symbol . This wire must be longer than the other wires. Remove the terminal block cover (A), undoing the screw and inserting the cover in the terminal block hinge (B). 70 mm of sheath from the power supply cable. Insert the power supply cable into the cable clamp and connect the wires to the terminal board as indicated in the diagram next to the terminal board itself. Secure the power cable with the cable clamp. Close the cover (C) and screw it on the terminal block with the removed screw - point (1). [. . . ] • At this stage, light up the burners and turn the knobs from max position to minimum position to check flame stability. After adjusting, restore the seals with sealing wax or equivalent material. TROUBLESHOOTING GUIDE (INDUCTION ZONE) • • • • • Before contacting After-sales Service: read and follow the instructions given in the section “Operating instructions”. Connect the hob to the electricity supply and check that the supply has not been shut off. If, when the hob is switched on, alphanumeric codes appear on the display, consult the following table for instructions. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL AKT 477/IX

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL AKT 477/IX will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag