User manual WHIRLPOOL AKT 653/NB PROGRAM CHART

[. . . ] Keep the packaging material (plastic bags, polystyrene parts, etc. ) out of the reach of children, as they are potentially dangerous. Check whether the hob has been damaged during transport and remove any protective film from the appliance parts. This hob is designed solely for household use for cooking food. Any other use (such as heating rooms) is to be considered improper and, as a consequence, dangerous. [. . . ] The outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations. Combustion products are discharged outdoors through specific hoods or wall and/or window mounted electrical fans. PROVISION FOR VENTILATION ROOM VENTILATION To ensure correct operation of the appliance, the room size in which it is to be installed shall be in accordance with AS5601. This room must also be continuously ventilated, fresh air should flow through permanent openings in walls to outside or to an adjacent non-inhabitable room as detailed is AS 5601. These permanent openings must be made in such a way that it cannot be obstructed from either side of the wall, also they should be protected by plastic grids, metallic mesh, etc. , taking care not to reduce the air vent effective area mentioned above and located near floor level and positioned so as not to interfere with the operation of the exhaust system, the minimum cross section of these permanent openings is set by AS5601. • - OVERHEAD CLEARANCE Range hoods and exhaust fans shall be installed in accordance with the manufactures instructions. However, in no case shall the clearance between the top of the highest burner of the cooking appliance and the range hood be less than 600mm or, for an overhead exhaust fan, 750mm Any downward facing combustible surface less than 600mm above the top of the highest burner shall be protected for the full width and depth of the cooking surface area in accordance with Clauses 5. 12. 1. 2 of AS 5601 However, in no case shall this clearance to any surface be less than 450mm. SIDE CLEARANCE Where the distance measured between the periphery of the burner and any vertical combustible surface is less than 200mm, the surface shall be protected in accordance with Clause 5. 12. 1. 2 of AS5601 to a height of not less than 150mm above the hotplate top surface for the full length and width of the cooking surface area. Note: the cooking surface area is defined as the part of the appliance where the cooking normally takes place and does not include those parts of the appliance containing the control knobs. INSTALLATION GAS CONNECTION 1. 5. ELECTRICAL CONNECTION • • • The electrical connections must comply with local regulations. The data relevant to the voltage and power absorption are indicated on the rating plate. The earthing of this appliance is compulsory by law. L Earth (yellow/green) N 6. 10. Check the “gas type” sticker attached to the hotplate. Details of the injector sizes used are recorded on the data plate located on the base of the appliance. If necessary, the electrical power cable must be replaced exclusively with a power cable having identical characteristics to the original supplied by the manufacturer (type H05V2V2-F T90°C or H05RR-F). This operation must be performed by a qualified electrician. ASSEMBLY After having cleaned the perimeter surface, apply the supplied gasket to the hob as shown in the figure. GAS CONNECTION POINT ELECTRICAL CONNECTION POINT Position the hob in the worktop opening made respecting the dimensions indicated in the Product Description Sheet. Fig. 3 Note: the power supply cable must be long enough to permit its upward extraction. Fig. 2 To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow and fasten them by means of their screws in accordance with the thickness of the worktop (see figures on the right). Top 40 mm Top 30 mm Top 20 mm ADJUSTMENT TO DIFFERENT TYPES OF GAS If the appliance is intended to operate with a different gas from the gas type stated on the rating plate change the injectors. Use pressure regulators suitable for the gas pressure indicated in the Product Description Sheet. • The gas nozzles must be changed by After Sales Service or a qualified technician. • Nozzles not supplied with the appliance must be ordered from After Sales Service. • Adjust the minimum setting of the taps. Note: when liquid petroleum gas is used (ULPG), the minimum gas setting screw must be tightened as far as it will go. Should you experience difficulty in turning the burners knobs, please contact the After Sales Service for the replacement of the burner tap if found to be faulty. • • Do not use flammable products. [. . . ] • The minimum gas setting is correct (see relevant paragraph). The containers are not stable Check that: • The bottom of the container is perfectly flat • The container is centered on the burner. • The grids have not been exchanged or positioned incorrectly. If any repairs are required, please contact an authorised After-Sales Service, as indicated in the warranty. [. . . ]