User manual WHIRLPOOL AKT 661/IXL PROGRAM CHART

[. . . ] max. PRATICAL ADVICE FOR USING THE BURNERS For better burner performance, please stick to the following rules: Use pots and pans that fit the burners (see table on the right). Use the correct amount of water for cooking foods and keep the pot covered. Burner ultra-rapid semi-rapid auxiliary NATURAL GAS (Methane) G20 17 20 25 Pot Ø from 24 to 26 cm from 16 to 22 cm from 8 to 14 cm LIQUID PETROLEUM GAS (Butane) G30 LIQUID PETROLEUM GAS (Propane) G31 Type of gas used G20 20 mbar G30 28-30 mbar G31 37 mbar 20 28-30 35 25 37 45 Air necessary (m3) for the combustion of 1 m3 of gas 9. 52 30. 94 23. 8 ELECTRIC SUPPLY: 230 V ~ 50 Hz 5019 319 01555 To get full satisfaction from the hob, please read these instructions carefully and keep them for future consultation. PRECAUTIONS AND GENERAL ADVICE To get full satisfaction from your hob, please read these instructions carefully and keep them for future consultation • • • • • • • These instructions are only valid for those Countries where the destination abbreviations are mentioned on the product description sheet and on the hob. Keep the packaging material (plastic bags, polystyrene parts, etc. ) out of the reach of children, as they are potentially dangerous. [. . . ] Before closing it, make sure that all the burners are off. After use, make sure that the knobs are in position OFF and close the main gas delivery or cylinder tap INSTALLATION TECHNICAL INFORMATION FOR THE INSTALLER • • This product can be embedded in a worktop 20 to 40 mm thick. If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the work surface. This panel must be positioned at a maximum distance of 150 mm below the upper surface of the work surface but, in no case less than 20 mm from the bottom of the hob. In the case that you intend to install an oven beneath the hob, make sure that it is manufactured by Whirlpool and equipped with a cooling system. The manufacturer declines all liability if another brand oven is installed beneath the hob. Before installation, make sure that: the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see the rating plate and injector table). The outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations. Combustion products are discharged outdoors through specific hoods or wall and/or window mounted electrical fans. PROTECTING THE ENVIRONMENT 1. Packaging The packaging material is entirely recyclable, and is marked with the recycling symbol , which identifies it as a type of material that must be sent to local waste-disposal centres. This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. INSTALLATION GAS CONNECTION • • • The gas supply system must comply with local regulations. You can find specific local regulations for some countries in the paragraph “Reference to Local Regulations”. If no information concerning your Country is given, please ask details to your Installer. The connection of the hob to the gas pipe network or gas cylinder must be made by means of a rigid copper or steel pipe with fittings complying with local regulations, or by means of a continuous-surface stainless steel hose complying with local regulations. The maximum length of the hose is 2 linear metres. Before connecting the tube to the elbow fitting (A), interpose the washer (B) supplied, in compliance with EN 549. Top 40 mm Position the hob in the worktop opening made respecting the dimensions indicated in the Product Description Sheet. Note: the power supply cable must be long enough to permit its upward extraction. [. . . ] Note: Failure to comply with these instructions may compromise the safety and quality of the product. • • • • CLEANING THE HOB PARTS • • • • • • Grids, burner caps and burners can be removed to be cleaned. Clean them by hand with warm water and non-abrasive detergent, carefully removing any food residues and checking that none of the burner openings is clogged. Refit burners and burner caps correctly in the respective housings. When replacing the grids, make sure that the panstand area is aligned with the burner and that the burner feet are fitted in the respective housings on the hob surface. [. . . ]