User manual WHIRLPOOL AKT 699/IX INSTRUCTION FOR USE

[. . . ] 1935/2004 • • • • • • • These instructions are only valid for those Countries where the destination abbreviations are mentioned on the product description sheet and on the hob. Keep the packaging material (plastic bags, polystyrene parts, etc. ) out of the reach of children, as they are potentially dangerous. Check whether the hob has been damaged during transport and remove any protective film from the appliance parts. This hob (Class 3) is designed solely for household use for cooking food. [. . . ] metallic mesh) - Two burners for the same pot • In the event of prolonged use, additional ventilation may be needed (opening a window or increasing the extraction force of the hood). • The appliance is not intended for use by people (children included) with physical, sensory or mental impairment or without experience and knowledge of the appliance, unless supervised or previously instructed in its use by those responsible for their safety. • Keep children away from the hob when it is in use and do not let them play with the controls or any other appliance parts. Warning: the protective rubber feet on the grids represent a choking hazard for young children. After removing the grids, please ensure that all the feet are correctly fitted. • Attention: the glass lid (if provided) may shatter if overheated. Before closing it, make sure that all the burners are off. After use, make sure that the knobs are in position OFF and close the main gas delivery or cylinder tap INSTALLATION TECHNICAL INFORMATION FOR THE INSTALLER • • This product can be embedded in a worktop 20 to 40 mm thick. If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the work surface. This panel must be positioned at a maximum distance of 150 mm below the upper surface of the work surface but, in no case less than 20 mm from the bottom of the hob. If there is an oven beneath the hob, make sure that it is manufactured by Whirlpool and equipped with a cooling system. • After connection to the gas supply, check for leaks with soapy water. ADJUSTMENT TO DIFFERENT TYPES OF GAS If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and orange sticker applied on the top of the hob, change the injectors. Remove the orange sticker and keep it with the instructions booklet. Use pressure regulators suitable for the gas pressure indicated in the Product Description Sheet. L Earth (yellow/green) N ELECTRICAL CONNECTION • • • The electrical connections must comply with local regulations. The data relevant to the voltage and power absorption are indicated on the rating plate. The earthing of this appliance is compulsory by law. • • • The gas nozzles must be changed by After Sales Service or a qualified technician. Nozzles not supplied with the appliance must be ordered from After Sales Service. Adjust the minimum setting of the taps. Note: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it will go. Should you experience difficulty in turning the burners knobs, please contact the After Sales Service for the replacement of the burner tap if found to be faulty. • • • The manufacturer cannot be held responsible for any injury to persons or animals or damage to property arising from failure to comply with these requirements. When the hob is installed, provide a single-pole circuit breaker with a contact separation of at least 3 mm. If necessary, the electrical power cable must be replaced exclusively with a power cable having identical characteristics to the original supplied by the manufacturer (type H05V2V2-F T90°C or H05RR-F). This operation must be performed by a qualified electrician. REPLACING THE INJECTORS (see the injector table in the Product Description Sheet) • • • • Remove grids (A) Extract burners (B) Using a socket spanner of the appropriate size unscrew the injector (C) Replace it with the injector suitable for the new type of gas. Assembly 1. [. . . ] Before calling the After-Sales Service, refer to the Troubleshooting Guide to determine the problem. 1. • • • • • • 2. The burner fails to ignite or the flame is not even Check that: The gas or electrical supplies are not shut off and especially that the gas supply tap is open. The gas cylinder (liquid gas) is not empty. All the burner parts have been positioned correctly. The burner does not stay lit Check that: When lighting the burner, the knob has been pressed for enough time to activate the protection device. [. . . ]