User manual WHIRLPOOL AKT 709/IX PROGRAM CHART

[. . . ] made 2. 5 Normallypolyamide (Perlon, Nylon) or blends withof polyester (Diolen, Trevira), cotton. ❉ Yes ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ 1200 Synthetics 30 - 40 - 60 °C Delicates 30 - 40 °C Sintéticos 30 - 40 - 60 °C Delicados 30 - 40 °C ❉ ❉ — — — Yes Yes Yes Yes Yes ❉ ❉ ❉ ❉ ❉ ❉ ❉ — — — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — ❉ — — — — ❉ ❉ — — — ❉ — ❉ ❉ ❉ ❉ ❉ ❉ — — — — ❉ ❉ ❉ ❉ ❉ ❉ ❉ — — — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — 1000 1) 1000 1) 1200 1200 1000 1) 1. 5 Curtains and delicate clothing, dresses skirts, shirts and blouses. 3. 0 Slightly to normally soiled textiles made of cotton and/or synthetics. worn outer 3. 0 Shortlywith cotton. clothing made of cotton, polyester, polyamide and blends Only woollens with a felt-free finish, labelled with the woolmark and Daily load 40 °C Diario 40 °C ❉ — — Quick wash 30 °C Rápido 30 °C Wool Cold - 40 °C Lana/lã frío - 40 °C 1. 0 identified as machine washable. If you select “Rinse Hold” do not leave items to soak for too long. Textiles made of linen, silk, wool and viscose marked as Handwash 30 - 40 °C A mano/mão 30 - 40 °C 1. 0 “handwashable”. [. . . ] . . after having pressed the “Start/Pause” button: • Press the “Reset” button for at least 3 seconds - the start delay time disappears from the time display. PROGRAMME START Open the tap and press the “Start/Pause” button. The indication lamp next to the “Start/Pause” button lights up. The programme sequence indicator shows the current programme phase, running from left to right through Wash, Rinse, Spin/Drain. The time display shows the remaining programme time. Due to variations in load and temperature of inlet water, the remaining time is newly calculated in certain programme phases. If this is the case, an animation appears on the time display. “DOOR OPEN” INDICATION Before starting and after end of a programme, the lamp lights to show that the door can be opened. As long as a wash programme is running, the door remains locked and must on no account be forced open. In case you have an urgent need to open it during a running programme, refer to “Cancel (Reset) a running programme before the end”. RED INDICATIONS “Service” Lighting up of the “Service” indication can be caused by a fault in an electrical component. Refer to the “Troubleshooting Guide” in your Instructions for Use; if the fault persists, contact our After Sales Service. “Water tap closed” The appliance has no or insufficient water supply. Open the water tap; if the indication still lights up, refer to the “Troubleshooting Guide” in the Instructions for Use. “Clean pump” Waste water is not pumped out. Check whether the drain hose is kinked or the filter must be cleaned; in the latter case refer to the Instructions for Use (“Removing the Filter”). PROGRAMME END • All the lights of the programme sequence indicator are off, and the “Door open” indication lights up. Turn the programme selector to the “Off/O” position. Leave the door ajar to allow the drum to dry. CHANGE PROGRAMME AND/OR OPTIONS AFTER PROGRAMME START 1. Press the “Start/Pause” button to pause the programme. Select the new programme (with temperature), any options and another spin speed if you want. Press the “Start/Pause” button again. [. . . ] “Cold wash” button • Water is heated only up to 20°C. • Suitable for delicate laundry items with wash temperature recommendation of max. • Selectable only on the lowest temperature step of each programme. “Rinse hold” button • The laundry remains in the last rinse water without progressing to the final spin cycle to avoid creasing and prevent colours from changing. [. . . ]