User manual WHIRLPOOL AKT 920/IX INSTRUCTION FOR USE

[. . . ] BURNER Pressure (kPa) Burner Auxiliary semi-rapid Rapid 4 rings Fish kettle (23 x 8 cm) Pot Ø from 8 to 14 cm from 16 to 22 cm from 24 to 26 cm from 24 to 26 cm 31 x 16 cm ELECTRIC SUPPLY: 230 -240 V - 50 Hz Front RHS (Semi-rapid) Rear RHS (Rapid) Front LHS (4 rings WOK) Rear LHS (Auxiliary) Middle HS (Fish kettle) 1. 00 1. 00 1. 00 1. 00 1. 00 • - NOTE: In case of installation of a hood above the cooktop, please refer to the hood instructions for the correct distance. NG Injector (mm) 1. 15 1. 60 1. 75 0. 85 1. 60 Rate MJ/h 7. 0 12. 5 14. 8 4. 0 13. 0 Pressure (kPa) 2. 75 2. 75 2. 75 2. 75 2. 75 ULPG Injector (mm) 0. 60 1. 00 1. 00 0. 55 0. 95 Rate MJ/h 5. 0 15. 0 15. 1 4. 0 11. 5 PRATICAL ADVICE FOR USING THE BURNERS For better burner performance, please stick to the following rules: Use pots and pans that fit the burners (see table on the right). Use the correct amount of water for cooking foods and keep the pot covered. In the case of pans with convex bottoms (WOK), use the support grille provided, which should be positioned only on the 4 ring burner. [. . . ] The earthing of this appliance is compulsory by law. L Earth (yellow/green) N 6. 10. Check the “gas type” sticker attached to the hotplate. Details of the injector sizes used are recorded on the data plate located on the base of the appliance. This appliance shall be installed in accordance with installation requirements of the local gas authority to the appropriate installation code (AS5601). Before installing the hotplate consider the location of the gas supply and routing the gas line. For ULPG models the gas supply for the hotplate must be regulated to a pressure of 2. 75kPa. The gas inlet connection fitting is ½” B. S. P female thread. For NG models the gas supply is connected to a regulator which is supplied. The inlet connection has ½” B. S. P male thread. IT IS ESSENTIAL THAT THE ELBOW ON THE APPLIANCE BE HELD FIRMLY WITH A SPANNER. The regulated pressure for NG is 1. 00kPa. A manual shut-off valve must be installed in the gas line, in an accessible position external to the hotplate, so that in the event of an emergency or service, the gas supply can be shutoff. For gas inlet position of appliance refer Fig. After installing the gas supply and making all connections check thoroughly for possible leaks. Turn all control knobs on the unit to “OFF” position. Using a soap and water solution check each gas connection one at a time, by brushing the solution over connection. Presence of bubbles will indicate a leak. Tighten the fitting and re-check for leaks. If it is not possible to correct the leak, replace fitting. Under no circumstance use matches or flame for checking leaks. Turn on appliance gas cock and light each burner. Check for a clear blue flame without yellow tipping. [. . . ] Note: Failure to comply with these instructions may compromise the safety and quality of the product. Customer Service: 1300 363 344 Service Call Booking: 1300 361 166 CARE AND MAINTENANCE CLEANING THE HOB SURFACE • • To maintain your hob in perfect conditions, clean it after every use, removing any food spills. Before any cleaning operation, disconnect the hob from the mains and wait for it to cool down. • • All the enamelled and glass parts should be cleaned with warm water and neutral solution. Stainless steel surfaces may be stained by calcareous water or aggressive detergents if left in contact for too long. [. . . ]