User manual WHIRLPOOL AKZ 390 NB INSTRUCTION FOR USE

[. . . ] The oven can also be fitted under a cooktop. *: 590 For D+CH only * A A A A • There must be a gap of at least 5 mm between the upper edge of the oven and the lower edge of the working surface. This gap must never be closed by strips or unit reinforcing pieces. When the oven is installed, make sure that the sides do not touch the front edges of the unit or the adjacent drawers and door (see below picture). No Contacts 2 3gb66016. fm5 Page 3 Tuesday, April 16, 2002 3:27 PM ELECTRICAL CONNECTION • Do not switch on the oven before connection is complete. • Make sure that the installation and the electrical connection are made by a qualified engineer according to the manufacturer's instructions and the local rules in force. [. . . ] Maximum weight: 7 Kg. Fum es E x hau st 4 3gb66016. fm5 Page 5 Tuesday, April 16, 2002 3:27 PM OVEN ACCESSORIES • Accessories supplied depend on the model (refer to the Product Description Sheet supplied separately). Bar rack The bar rack can be used in the same way as a flat rack. The number of shelf positions can be doubled, depending on whether the rack is inserted in the (A) or (B) position. Multi-purpose drip tray This tray can also be used as a baking tray, and has a sloping edge for this purpose. Use as a baking tray for cream puff, meringues, madeleines, puff pastry, etc. When placed under a rack, it acts as a drip tray to collect dripping juices and fat from grilling dishes. Turnspit The turnspit comes supplied with a stand for the spit. To use the turnspit: • Fit the spit stand in position in the oven. • Slide one of the forks on to the spit, followed by the food to be spit-roasted, then the second fork. Centre the food and secure in position by screw-tightening the two forks. • Brush the food with oil or softened butter. • Insert the tip of the spit in the turning square at the back of the oven. • Set the selector to the GRILL + TURNSPIT position. Before closing the door, remove the heat-insulated handle from the spit by unscrewing. 5 3gb66016. fm5 Page 6 Tuesday, April 16, 2002 3:27 PM CLEANING THE OVEN AND ITS ACCESSORIES • After each use leave the oven to cool and clean it to avoid the encrustations being repeatedly heated. • If the dirt is tough, use a specific oven cleaning product following the instructions on the packaging. • Clean the outside with a sponge dampened with lukewarm water. • Clean the oven door glass with a liquid detergent. • Wash the accessories in the dishwasher or by hand using an oven cleaning product. • If cooking lasts for a long time, or when cooking simultaneously on several levels, food containing a large amount of water (pizza, stuffed vegetables, etc. ) may create condensation on the inside of the door and on the gasket; when the oven has cooled, dry with a cloth or a sponge. Additional information for appliances which have an aluminium front: The material has a sensitive surface. In order to avoid scratches, only use a soft sponge and liquid cleaner to clean the front of the appliance. Removing the oven door To remove the oven door, guide the lever (A) into the hinge notch (B): close the door to its stop position and pull out towards you. Refit in the reverse order. Changing the oven light bulb Disconnect the oven from electrical supply. To remove and replace the bulb, remove the cover (H). Proceed as shown in the diagram opposite. Remember to replace the seal (J). Self-cleaning system This oven burns off splashes and deposits at high temperature. The smoke produced is cleaned by being passed through a catalyser. [. . . ] If the display shows the message F+ numeric code (e. g. : F01), contact the After Sales Service, quoting the error code displayed. If the appliance still fails to function properly, please call After Sales Service. 7 3gb66016. fm5 Page 8 Tuesday, April 16, 2002 3:27 PM AFTER SALES SERVICE • Before contacting AFTER SALES SERVICE: 1. See whether you can solve the problem yourself (see “Trouble-shooting guide”). Switch the appliance off and on again to see whether the problem has disappeared. [. . . ]