User manual WHIRLPOOL AMB 888/G INSTRUCTION FOR USE

[. . . ] 33933047GB. fm Page 28 Monday, January 10, 2005 1:03 PM INSTRUCTIONS FOR USE SPLIT CEILING-MOUNTED AIR CONDITIONER WITH GREEN GAS PREPARATION BEFORE USE SAFETY PRECAUTIONS IDENTIFICATION OF PARTS REMOTE CONTROL OPERATION INSTRUCTIONS MAINTENANCE PROTECTION TROUBLESHOOTING INSTALLATION INSTRUCTIONS ELECTRICAL CONNECTION This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). This guideline is the frame of a European-wide validity of return and recycling on Waste Electrical and Electronic Equipment. 28 33933047GB. fm Page 29 Monday, January 10, 2005 1:03 PM PREPARATION BEFORE USE Before using the air conditioner, be sure to check and preset the following. • Remote Control presetting The remote control is NOT preset as Cooling Only Air Conditioner or Heat Pump by manufacturer. [. . . ] • Remove the air filter. Air filter cleaning Cleaning • Remove the dust from the air filter with a vacuum cleaner. • Clean it with water and neutral detergent. • Dry it thoroughly in a cool and shaded place. Note: Do not place the filter next to high heat or fire, it may cause ageing, deformation or even burning of the plastic parts. • Replace the filter in its original position after cleaning. • Lock the four corners of the air filter. • Refit the air intake grill. Air intake grill cleaning • Unplug from the power supply, then use a ladder or other safe means to gain access the indoor unit. • Press the buttons on the air intake grill with both hands. • Remove the air intake grill. • • • • • Open the air intake grill. Grasp both sides and remove it as shown below. Clean it with water and neutral detergent. Dry it thoroughly in a cool and shaded place. Grasp both sides of the air intake grill and replace it in reverse order to refit the air intake grill. Before using a ladder or other means, inspect it to make sure it is safely placed. 37 33933047GB. fm Page 38 Monday, January 10, 2005 1:03 PM PROTECTION Operating condition The protective device may trip and stop the appliance in the cases listed below. Outdoor air temperature is over 24°C HEATING Outdoor air temperature is below -5°C Room temperature is over 27°C COOLING DRY Outdoor air temperature is over 43°C Room temperature is below 21°C Room temperature is below 18°C If the air conditioner runs in “COOLING” or “DRY” mode with door and/or window open when relative humidity is higher than 85%, dew will drip down from the outlet. Protection device features The protection device will trip in the following cases: • After stopping the appliance and restarting it immediately or after changing mode during operation, there is a delay of 3 minutes before it starts operation. • Switching on power supply and turning on the appliance at once, you need to wait about 20 seconds. • If all operation has stopped, press the “ON/OFF” button again to restart. Set the timer again if it has been cancelled. Noise pollution • Install the air conditioner in a place that can bear its weight in order to operate more quietly. • Install the outdoor unit in a place where the air discharged and the operating noise do not annoy your neighbours. • Do not place an obstacle in front of the outlet of the outdoor unit as it may affect the air conditioner operation and increase the noise level. Inspection After using the appliance for a long time, the following items should be inspected: • Power supply cord and plug overheating or even a burned smell. • Abnormal operating sound or vibration. IMPORTANT: Stop the air conditioner if any fault occurs. It is advisable to check the air conditioner carefully every five years even if none of the above faults occur the air conditioner. HEATING mode features Preheating At the beginning of HEATING operation, the airflow from the indoor unit is discharged 2-5 minutes later. [. . . ] Note: After adjusting the level and drain system of the unit, do the following: Front panel installation • Remove the 4 corner panels from the air intake grill on the front panel shown on the right. 49 33933047GB. fm Page 50 Monday, January 10, 2005 1:03 PM Main Unit Front panel • Buckle the front panel to the main unit, paying attention to the correct direction of the front panel. Two of the buckles hook inside, while the other two hook outside. • Connect the three connectors of front panel to the main unit, which connect the two fan motors and remote control indicator panel on the front panel to the control PCB on the main unit. • Fix the front panel by tightening the screws on the 4 corners, until it adheres firmly to the ceiling board (see figure above right). [. . . ]