User manual WHIRLPOOL AMB 966 INSTRUCTION FOR USE

[. . . ] 33933049GB. fm Page 4 Monday, January 10, 2005 5:27 PM INSTRUCTIONS FOR USE SLIM RANGE SINGLE SPLIT AIR CONDITIONER WITH ECOLOGICAL GAS AND WITH GAS R22 PREPARATION BEFORE USE SAFETY PRECAUTIONS IDENTIFICATION OF PARTS REMOTE CONTROL OPERATION INSTRUCTIONS MAINTENANCE TROUBLESHOOTING PROTECTION INSTALLATION INSTRUCTIONS SLIM RANGE R22 SLIM RANGE This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). This guideline is the frame of a European-wide validity of return and recycling on Waste Electrical and Electronic Equipment. 4 33933049GB. fm Page 5 Monday, January 10, 2005 5:27 PM PREPARATION BEFORE USE Before using the air conditioner, be sure to check and preset the following. • Remote Control presetting The remote control is NOT preset as Cooling Only Air Conditioner or Heat Pump by manufacturer. [. . . ] If the desired time is beyond 10 hours, the set time increases or decreases by 1 hour. The time that can be set ranges between 0. 5 and 24 hours. 3. cancelling the switch-on time after 9. 5 hours To cancel the set time: press the TIMER button again, a “beep” can be heard and the timer indicator on the indoor unit lights off. JET mode • JET mode is used to start or stop fast cooling. Fast cooling operates at high fan speed, changing the set temperature automatically to 18°C. • JET mode can be set when the appliance is in operation or energized. • In JET mode, you can set airflow direction and timer. If you want to quit from JET mode, press any-JET, MODE, FAN, ON/OFF or TEMPERATURE SETTING button, the display will return to the original mode. Note: SLEEP and 6th Sense buttons are not available in JET mode. 12 33933049GB. fm Page 13 Monday, January 10, 2005 5:27 PM Sleep mode SLEEP mode can be set in COOLING or HEATING operation mode. This function gives you a more comfortable environment for sleep. In SLEEP mode, • The appliance will stop operation automatically after operating for 8 hours. • Fan speed is automatically set at low speed. • *The set temperature will rise by max. 1°C if the appliance operates in cooling mode for two hours, then it will remain constant. • The set temperature will decrease by max 3°C is the appliance operates in heating mode for 3 hours, then it will remain constant. COOLING 8 hours timer 1 hour 1 hour 1 Rise by 0. 5°C SET TEMP. START STOP Rise by 0. 5°C **HEATING 8 hours timer 1 hour SET TEMP. 1 hour Decrease by 1°C Decrease by START Decrease by 1 hour STOP *: In cooling mode, if room temperature is 26°C or above, set temperature will not change. **: Heating is NOT available for cooling only air conditioner. 13 33933049GB. fm Page 14 Monday, January 10, 2005 5:27 PM MAINTENANCE Appliance maintenance Unplug from the power supply Stop the appliance before unplugging. • To remove the front panel pull it outwards as shown in the figure (a) Wipe with a soft, dry cloth Use lukewarm water (below 40°C) to clean the appliance when it is very dirty. • Use a dry and soft cloth to clean it. Never use volatile substances such as gasoline or polishing powder to clean the unit. Never sprinkle water on the indoor unit • Danger! [. . . ] Do not let air enter the refrigerating system or discharge refrigerant when moving the air conditioner. Test run the air conditioner after finishing installation, and record details of operation. Type of fuse used on indoor unit control for 7 K, 9 K, 12 K is 50 T, with rating 2. 5 A, T, 250 V. For 18 K, 22 K, 24 K models use 5 A, T, 250 V. [. . . ]