User manual WHIRLPOOL AQUASTEAM 9770B WP INSTRUCTION FOR USE

[. . . ] The washing machine must be earthed by law. The manufacturer declines all liability for damage to property or injury to persons or animals due to non-compliance with the directions given above • Do not use extension leads or multiple sockets • Before any maintenance on the washing machine disconnect it from the mains supply • After installation, access to the mains plug or to disconnection from mains supply must be ensured at all times via a double-pole switch • Do not operate the washing machine if it has been damaged during transport. Inform the After-Sales Service • Mains cable replacement is only to be carried out by After-Sales Service • The appliance must only be used in the household for the prescribed uses 2. Remove the transport bolts • The washing machine is fitted with transport bolts to avoid any possible damage to the interior during transport. Before using the machine, it is imperative that the transport bolts are removed 3. Install the washing machine • Remove the protective film from the control panel • Move the appliance without lifting it by the worktop • Install the appliance on a solid and level floor surface, preferably in a corner of the room • Make sure that all four feet are stable and resting on the floor and then check that the washing machine is perfectly level (use a spirit level). 4. Water inlet • Connect the water supply inlet hose in accordance with the regulations of your local water company • Water inlet: Cold water only • Water tap: 3/4” threaded hose connector • Water pressure (flow pressure): 100-1000 kPa (1-10 bar). Minimum housing dimensions: Width: Height: Depth: 600 mm 825 mm 600 mm 18 Black process 45. 0° 100. 0 LPI 30105536aGB. fm Page 19 Thursday, December 30, 2004 10:53 AM PRECAUTIONS AND GENERAL RECOMMENDATIONS 1. Packaging • The packaging material is entirely recyclable, and marked with the recycling symbol . [. . . ] Select the “Rinse and Spin” programme, reduce the speed to 800 rpm and start the programme. Pull out the detergent drawer until you can see about 3 cm of chamber 5. while the water is running into the detergent drawer. 6. If there are starch residues in the detergent drawer when the programme has finished, clean if necessary (see “Cleaning and Maintenance”). Take note also of the starch manufacturer's instructions for use. 22 Black process 45. 0° 100. 0 LPI 30105536aGB. fm Page 23 Thursday, December 30, 2004 10:53 AM REMOVING THE FILTER We recommend that you check and clean the filter regularly, at least two or three times a year. Especially: • If the appliance is not draining properly or if it fails to perform spin cycles. • If the pump is blocked by a foreign body (e. g. buttons, coins or safety pins) IMPORTANT: make sure the water has cooled before draining the appliance. Open the filter cover with the aid of the coloured insert from the detergent container. Open the filter but do not remove it completely. Slowly turn the filter anticlockwise until the water begins to drain out. Now unscrew the filter completely and remove it. For models with a “Water tap closed” indicator lamp, the red indicator lamp lights up. Open the tap and press the “Start/Pause” button. The appliance stops during the programme (varies depending on model) Check whether: • the “Rinse Hold” indicator lamp is flashing; terminate this option by pressing the button again In models with LCD display: the “Rinse Hold” option has been preselected and the “Rinse Hold” symbol appears on the display; cancel this option by pressing the “ ” button or select the “Drain” programme • another programme has been selected and the “Start/Pause” indicator lamp is flashing. Reselect the desired programme and press the “Start/Pause” button • the door has been opened and the “Start/Pause” indicator lamp is flashing. Close the door and press the “Start/Pause” button again. In models with LCD display, the display shows: “PAUSE!” • the washing machine's safety system has been activated (see “Fault display chart”) The washing machine has an imbalance detection and correction system. If individual heavy items are loaded (e. g. bathrobes), this system may reduce the spin speed automatically or even interrupt the spin completely if it detects too great an imbalance even after several spin starts, in order to protect the washing machine. In models with LCD display, in the event of an imbalance, the display shows: • If the laundry is still too wet at the end of the cycle, add smaller articles of laundry and repeat the spin cycle • Excessive foam formation may prevent spinning. Use the correct amount of detergent In models with LCD display, the display shows: • Check that the spin speed selector has not been set to “0” 25 Black process 45. 0° 100. 0 LPI 30105536aGB. fm Page 26 Thursday, December 30, 2004 10:53 AM The programme time indicated on the remaining time display (if fitted) “jumps” up or down suddenly by several minutes, or the programme time shown initially is lengthened/ shortened by a period of time: This is a normal capacity of the washing machine to adapt to factors that the wash programme time can have an effect on, e. g. : • excess foam formation • load imbalance due to heavy items of laundry • prolonged heating time due to reduced delivery of hot water Because of influences like these, the time remaining in the programme run is recalculated, and updated if necessary. In addition, during the filling phase, the washing machine determines the load and if necessary adjusts the initial programme time displayed accordingly. Fault description table Small indicator light is on. [. . . ] Next, select and start the desired programme. For models with no fault display, the washing machine stops in the appropriate programme step. Switch the washing machine off and back on again to continue the programme. If the fault persists, please contact After Sales Service (see “After Sales Service”). d. Water Stop fault (if available) The “Water Stop” may have been triggered by: 1. [. . . ]