User manual WHIRLPOOL AR GA 001 IX INSTRUCTION FOR USE

[. . . ] • Do not pull the power supply cable in order to unplug the appliance. • The electrical components must not be accessible to the user after installation. • Do not touch the appliance with any wet part of the body and do not operate it when barefoot. • The appliance is not intended for use by persons (including children) with any physical, sensory or mental impairment, or without experience and knowledge of the appliance, unless supervised or previously instructed in its use by those responsible for their safety. [. . . ] This information may be found on the inside of the hood, under the grease filter. Power cable replacement (type H05 VV-F 3 x 0, 75 mm2) must be carried out by a qualified electrician. If the hood is fitted with an electric plug, connect the plug to a socket complying with current regulations, located in an accessible place after installation. If no plug is fitted (direct wiring to the mains), or if the socket is not located in an accessible place, install a standardised double pole power switch that will enable complete isolation from the mains in case of category III overvoltage conditions, in accordance with installation rules. GENERAL RECOMMENDATIONS Before use Remove cardboard protection pieces, protective film and adhesive labels from accessories. Check the appliance for any transport damage. During use To avoid any damage do not place any weights on the appliance. Do not expose the appliance to atmospheric agents. SAFEGUARDING THE ENVIRONMENT Disposal of packing The packing material is 100% recyclable and is marked with the recycle symbol and in full compliance with local authority regulations governing waste disposal. Scrapping the product This appliance is marked in compliance with European Directive 2002/96/EC, Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The symbol on the product or on the accompanying documentation indicates that it should not be treated as domestic waste but must be taken to an appropriate collection centre for the recycling of electrical and electronic equipment. The various parts of the packing must therefore be disposed of responsibly GB9 TROUBLESHOOTING GUIDE The appliance does not work: • Check for the presence of mains electrical power and if the appliance is connected to the electrical supply. • Turn off the appliance and restart it to see if the fault persists. The hood's suction level is not sufficient: • Check the suction speed and adjust as necessary: • Check that the filters are clean: • Check the air vents for any obstructions. • Check the light bulb and replace if necessary; • Check that the light bulb has been correctly fitted. AFTER-SALES SERVICE Before calling the After-Sales Service: 1. See if you can solve the problem yourself with the help of the suggestions given in the "Troubleshooting guide". Switch the appliance off and back on again it to see if the fault persists. If after the above checks the fault still occurs, get in touch with the nearest After-Sales Service. Always specify: • A brief description of the fault; • The exact type and model of the appliance; • The service number (number after the word "Service" on the rating plate), located on the inside of the appliance. The service number is also indicated on the guarantee booklet; • Your full address; • Your telephone number. If any repairs are required, please contact an authorised After-sales Service (to guarantee that original spare parts will be used and repairs carried out correctly). CLEANING WARNING - Never use steam cleaning equipment. - Disconnect the appliance from the power supply. IMPORTANT: do not use corrosive or abrasive detergents. If any of these products accidentally comes into contact with the appliance, clean immediately with a damp cloth. [. . . ] IMPORTANT: It is advisable to install the hood before the side wall units. b) Lift the panel and centre it on the hood structure, respecting: the alignment between the bottom part of the panel and that of the hood, and the alignment between the position of the middle logo on the panel and the hood pushbutton panel under the structure. c) Fixing the decorative panel on the structure: slide the two bottom pins of the panel into the two bottom slots in the structure; d) Panel safety fixing: secure the panel to the hood structure with the two top screws. IMPORTANT: Make sure the panel is fixed securely to the structure. [. . . ]