User manual WHIRLPOOL AWG 452 PRODUCT FICHE

[. . . ] • Install the appliance on a solid and level floor surface, preferably in a corner of the room. • Make sure that all four feet are stable and resting on the floor and then check that the appliance is perfectly level using a spirit level (see Installation/ Adjust the feet”). 4. Water supply • Connect the water supply inlet hose in accordance with the regulations of your local water company (see “Installation/Connect the water inlet hose”). • Water supply: Cold water only • Tap: 3/4” threaded hose connector. • Pressure: 0. 05-1. 00 MPa (0. 5-10 bar). 6 Black process 45. 0° 150. 0 LPI 30120028GB. fm Page 7 Wednesday, May 3, 2006 3:26 PM PRECAUTIONS AND GENERAL RECOMMENDATIONS 1. Packing • The packing material is recyclable as indicated by the recycling symbol . [. . . ] By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. 7 Black process 45. 0° 150. 0 LPI 30120028GB. fm Page 8 Wednesday, May 3, 2006 3:26 PM DESCRIPTION OF THE APPLIANCE 1. Door handle • To open the door press the button inside the handle and pull. • Close the door by pushing it firmly (the lock will click into place) 6. After-Sales Service sticker (inside door) 8. Technical specifications sticker (inside cover) 1 3 2 4 7 5 8 6 9 Minimum housing dimensions Width Height Depth (depending on the appliance) 595 mm 850 mm 395 or 335 mm / 530 or 580 mm FILLING THE DETERGENT AND ADDITIVES 1. Pull out the detergent dispenser completely, until the limit. Add the detergent: • Programme with pre- and main wash • Main wash programme without prewash • Fabric softeners, conditioners and chlorine bleach: no more than to “MAX” mark • Stain remover • Water softener (water hardness class 4) • Starch (dissolved in water) 3. Screw the supply hose back onto the tap. Remove the filter from the appliance with pliers and clean it. Refit the filter and screw the hose connection to the appliance. Turn on the tap and ensure that the connections are completely water-tight. Water hose mesh strainer Check and clean periodically. For appliances with a straight water supply hose TRANSPORT / HANDLING Never move the appliance by carrying it by the worktop. 1. Eliminate all water from the hoses and from the appliance (see “Removing the Filter”, “Draining residual water”). Fit the transport bolts (obligatory) (see “Installation”). 10 Black process 45. 0° 150. 0 LPI 30120028GB. fm Page 11 Wednesday, May 3, 2006 3:26 PM INSTALLATION Remove the transport bolts For washing machines: 1. Slacken the three or four bolts (A) (according to model) with the spanner supplied. Slacken and remove the screws “A” which lock the drum during transport by following the instructions given at the side. Unscrew the bolts by hand. A B A B A B A A A B A A 1 1 For washing machines: 3. [. . . ] Secure the plywood sheet to the floor. Worktop for built-under models. The appliance must only be installed beneath a continuous fitted kitchen worktop. Unscrew the worktop fixing screws from the rear of the appliance. Lift the worktop slightly to free it from the housing of the top, then slide it forward to disengage it from the control panel, and remove. Install the cover panel following the relative instructions. [. . . ]