User manual WHIRLPOOL AWM 1008 INSTRUCTION FOR USE

[. . . ] made of polyester (Diolen, Trevira), polyamide (Perlon, Nylon) or blends with cotton. ❉ ❉ ❉ ❉ — — ❉ ❉ ❉ — — — — — — Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes ❉ ❉ ❉ ❉ ❉ ❉ — ❉ ❉ ❉ ❉ ❉ — ❉ — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — ❉ ❉ ❉ ❉ — — ❉ ❉ ❉ — — — — — — ❉ ❉ ❉ ❉ ❉ ❉ — — ❉ — — ❉ — — — ❉ ❉ ❉ ❉ — — — ❉ — — — — — — — 1200 20 to 95 1200 20 to 40 1000 1) 20 to 60 1200 20 to 60 1200 20 to 60 1200 20 to 30 1000 1) 20 to 60 1000 1) 20 to 95 1000 1) 20 to 40 1000 1) 20 to 40 800 1) 20 to 30 1200 20 to 60 1000 1) 1200 1200 5. 5 Normally soiled baby clothes made of cotton and/or linen. The washing liquid is rinsed out even more thoroughly and thus helps to protect sensitive baby skin. 11. 0 Programme for slightly to normally soiled fabrics made of cotton and/or synthetic fibres. 6. 0 Slightly soiled overalls and sports wear made of cotton, polyester, polyamide and blends with cotton. [. . . ] • Optimizes the additive's efficiency to get better wash performance and stain removal. • Select temperature of 30 or 40°C and use with maximum load. • Add an appropriate amount of in-wash additive for stain removal (powder) to the prewash chamber. • Appropriate for use of stain removers and bleaches on oxygen basis. Chlorine or perborate bleaches must not be used!➡ Normal “Soil level” modifier • Adapts the programme duration to the soil level of your laundry. PROGRAMME START Turn on the tap and press and hold the “Start (Pause)” button - the button's light stops blinking and goes on; it will take some time until water enters into the washing machine. The programme sequence indicator on the display shows the sequence reached in the programme. After starting the programme, the indication runs from left to right through “Add garment”, prewash, wash, rinse, spin. When a programme sequence is finished, the corresponding symbol goes off. The display shows the remaining programme time. Due to variations in load and temperature of inlet water, the remaining time is newly calculated in certain programme phases. If this is the case, an animation appears on the display and the and the “6th Sense” symbol lights up. ADD WASHING/DOOR LOCK As soon as a programme starts, the “Door locked” symbol lights up on the display. You can interrupt the programme by pressing “Start (Pause)” - the light blinks. The “Door locked” symbol on the display goes off and you can open the door. In certain programme phases, the “Door locked” symbol remains lit to show that the door cannot be opened in the present programme phase, e. g. when the water level is too high or during spinning. As long as the “Add garment” symbol lights up on the display, you can add more washing: press “Start (Pause)” , open the door, add your washing, close the door and press “Start (Pause)” to continue the programme. Prewash cycle increases programme duration by approximately 15 min. Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash. * The remaining time indicator can deviate from the values in the table, because it takes into account the operating conditions at that time. ** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out. *** Reference programme for energy label according to EN60456 and for comparative tests at test institutes. SAVE YOUR FAVOURITE PROGRAMMES If there is a programme setting which you use frequently, the washing machine offers the possibility to save one setting for each programme so that it can be used again by just pushing one button. [. . . ] Switch the machine off by pressing “On/Off” . Turn off the tap and open the door to unload your washing. Leave the door open for some time so that the washer’s inside can dry. Turn the programme selector to the desired programme - CHANGE THE PROGRAMME, TEMPERATURE, OPTIONS AFTER PROGRAMME START 1. Press the “Start (Pause)” button to interrupt the programme. [. . . ]