User manual WHIRLPOOL AWM 1400 EX INSTRUCTION FOR USE

[. . . ] 3gb05240. fm5 Page 2 Tuesday, October 2, 2001 5:03 PM ENGLISH FRANÇAIS NEDERLANDS ESPAÑOL PORTUGUÊS ITALIANO 7h5. d( Instructions for use Mode d’emploi Gebruiksaanwijzing Instrucciones para el uso Manual de utilização Istruzioni per l’uso . XOODQÕPWDOLPDWODUÕ Page 3 Page 21 Pagina 39 Página 57 Página 74 Pagina 91 6D\ID Black Process Plate 3gb05240. fm5 Page 3 Tuesday, October 2, 2001 5:03 PM CONTENTS BEFORE USING THE WASHING MACHINE FIRST WASH CYCLE PRECAUTIONS AND GENERAL RECOMMENDATIONS DESCRIPTION OF THE WASHING MACHINE CHILD SAFETY PREPARATION OF THE WASHING DETERGENTS AND ADDITIVES WASHING PROGRAMME REMOVING THE FILTER DRAINING RESIDUAL WATER CARE AND MAINTENANCE TROUBLESHOOTING GUIDE AFTER-SALES SERVICE TRANSPORT AND HANDLING INSTALLATION ELECTRICAL CONNECTION Black Process Plate 3gb05240. fm5 Page 4 Tuesday, October 2, 2001 5:03 PM BEFORE USING THE WASHING MACHINE 1. Removing the packaging and check • After unpacking, make sure that the washing machine is undamaged. If in doubt, do not use the washing machine. Contact After-Sales Service or your local retailer. • Keep the packaging materials (plastic bags, polystyrene parts, etc. ) out of reach of children, as they are potentially dangerous. 6. Electrical connections • Electrical connections must be carried out by a qualified technician in compliance with the manufacturer’s instructions and current standard safety regulations. [. . . ] For this programme do not add any further detergent. N. B. Programme interruption or pause To interrupt the running programme for a certain period and continue it at a later time: 1. Press the “Start/Pause” button. 2. Following the desired pause press the “Start/Pause” button once again. Cancelling the programme If the current programme is to be terminated prematurely and cancelled, the water must be pumped out first before the door can be opened: 1. Set the programme selector to programme setting “Drain”. The indicator (if available) above the “Start/Pause” button flashes. The spin indicator shows “0” and the remaining time indicator shows “0:02” minutes. 2. Press the “Start/Pause” button in order to start the “Drain” programme. 10 Black Process Plate 3gb05240. fm5 Page 11 Tuesday, October 2, 2001 5:03 PM REMOVING THE FILTER 1. Remove the coloured insert from the detergent dispenser and use it to open the filter cover. Turn the filter slowly anti-clockwise until the grip is vertical; do not extract filter as yet. Wait until all the water has drained out. Now unscrew the filter completely and extract it. Remove any foreign material from the filter. Make sure the pump impeller is not obstructed. Insert the filter and screw it fully down in a clockwise direction (until the grip is horizontal). 11. Pour 0. 5 l of water into the detergent dispenser to reactivate the “Eco System”. 12. Connect the appliance to the electrical socket. Check the filter two or three times a year and clean it if necessary. • Check the filter if the appliance is not draining properly or if it fails to perform spin cycles. • Remove the filter if the pump is blocked by an object (buttons, coins, safety pins, etc. ). IMPORTANT: Make sure the water has had time to cool before draining the appliance. DRAINING RESIDUAL WATER • Drain the residual water as described in the “Removing the Filter” chapter (points 1 to 8). • To drain the residual water from the pump, bend the machine frontward and operate as per points 9 and 10 of the previous chapter. • Before transporting (moving) the machine. [. . . ] If the hose is too short, replace it with a 3 m Water Stop hose (available from After-Sales Service or from your dealer). This operation must be carried out exclusively by a licensed electrician. The appliance must not be connected to the mixing tap of a nonpressurized water heater. The inlet hose and the plastic enclosure at the tap connection contain electrical components. [. . . ]