User manual WHIRLPOOL AWO 366 PROGRAM CHART

[. . . ] Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), polyamide (Perlon, Nylon) or blends with cotton. White Cotton 60 - 95 °C Kookwas 60 - 95 °C 6. 0 5. 0 2. 5 Coloured Cotton 40 °C Bonte was 40 °C ❉ Yes ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ max. Synthetics 30 - 40 - 60 °C Synthetisch 30 - 40 - 60 °C ❉ ❉ — — — — — — — — — Yes Yes Yes ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — — — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — — — — — — — — — — ❉ ❉ — — — — — — — — — ❉ — ❉ — — — — — — — — ❉ — ❉ — — — ❉ ❉ — — — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — — — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — 1000 1) 1000 1) max. Delicates 30 - 40 °C Fijne was 30 - 40 °C 1. 5 Curtains and delicate clothing, dresses skirts, shirts and blouses. 3. 0 Slightly to normally soiled textiles made of cotton and/or synthetics. Daily load 40 °C Gemengde was 40 °C Quick wash 30 °C 30 °C 3. 0 Shortly worn outer clothing made of cotton, polyester, polyamide and blends with cotton. Only woollens, labelled with the Woolmark and identified as machine washable. Yes max. Wool Cold - 40 °C Wol Koud - 40 °C 1. 0 1. 0 Yes Yes 1000 1) 400 2) Handwash 40 °C Handwas 40 °C Eco Cotton 60 °C Eco Katoen 60 °C Textiles made of linen, silk, wool and viscose marked as “handwashable”. [. . . ] • Press the “Start delay” button to select the delay time by 1 to 23 hours. • Press the “Start (Pause)” button. The countdown of the delay time begins; the “Start delay” indication lamp and the dot on the display will keep blinking until the programme starts. • The time delay indication disappears when the programme starts and it is replaced by the remaining programme time. • Once having pressed the “Start (Pause)” button, the number of hours preselected can be reduced by pressing again the “Start delay” button. To cancel the “Start delay” . . . before you press the “Start (Pause)” button: • Turn the programme selector to another position or press the “Reset” button. . . . after having pressed the “Start (Pause)” button: • Press the “Reset” button for at least 3 seconds - the start delay time disappears from the time display. Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash. * The remaining time indicator can deviate from the values in the table, because it takes into account the household conditions applicable at that time. ** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out. *** Reference Programme for Energy Label. ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE PROGRAMME Add detergent as indicated on the front page and as described in the chapter “Detergent and Additives” in your Instructions for Use. Turn the programme selector to the desired programme and temperature. The time display shows the duration of the chosen programme (in hours and minutes), and the “Start (Pause)” indication lamp blinks. The indication lamp of the predefined spin speed lights up. “Prewash” button • Only for heavily soiled loads (for example sand, granular dirt) sensible. Increases the cycle time by approximately 15 min. • Do not use liquid detergent for the main wash when activating the “Prewash” option. “Easy ironing” button • Can be used together with “Cotton”, “Synthetics” and “Daily load” programmes to make ironing easier. • Increases the water quantity and the clothes are spun very gently. “Intensive rinse” button • More water is added and rinse cycle is prolonged. • This option is particularly suitable for areas with very soft water, washing baby linen and helps people with allergies. “Rinse hold” button • The laundry remains in the last rinse water without progressing to the final spin cycle to avoid creasing and prevent colours from changing. • This option is particularly recommended for the programmes “Synthetics”, “Daily load” and “Delicates”. [. . . ] The new programme continues at the same position where the previous programme was interrupted. Do not add detergent for this programme. PROGRAMME START Open the tap and press the “Start (Pause)” button. The indication lamp of the “Start (Pause)” button lights up. The programme sequence indicator shows the current programme phase, running from left to right through Wash, Rinse, Spin/Drain. [. . . ]