User manual WHIRLPOOL AWO 6648 PRODUCT FICHE

[. . . ] Textiles made of linen, silk, wool and viscose marked as “handwashable”. If you select “Rinse Hold” do not leave items to soak for too long. A very gentle spin is used in this programme. Same as the last rinse and the final spin in the “Cotton” programme. [. . . ] For improved garment care, spin speed is restricted to 400 rpm in this programme. Whirlpool is a registered trademark of Whirlpool USA 5019 301 06151 Black process 45. 0° 150. 0 LPI 30106151GB. fm Page 2 Friday, March 7, 2008 3:12 PM CONSUMPTION DATA Programme Cotton Cotton Cotton with “Eco”*** Cotton Synthetics Synthetics Delicates Daily load Quick wash Wool Handwash Temperature (°C) 95 60 60 40 60 40 30 40 30 40 40 Load (kg) 6. 0 6. 0 6. 0 5. 0 2. 5 2. 5 1. 5 3. 0 3. 0 1. 0 1. 0 Water (l) 59** 49 49 56 50** 46 60 41 41 60 45 Energy (kWh) 1. 90 1. 14 1. 02 0. 70 0. 80 0. 50 0. 50 0. 50 0. 40 0. 50 0. 50 Approx. Programme Duration (hours : minutes)* 2:00 2:10 2:20 2:00 1:35 1:20 0:45 1:00 0:30 0:45 0:40 “Variable spin” button • Every programme has a predefined spin speed. • Press the button to set another spin speed. • If spin speed “0” is selected, the final spinning is cancelled but intermediate spin peaks remain during rinse. START DELAY The “Start Delay” allows to run the machine at the consumer’s convenience, for example at night when electricity is cheaper. • Select programme, temperature and options. • Press the “Start Delay” button to select the delay time by 1, 3, 6, 9 or 12 hours. • Press the “Start/Pause” button. The indication next to the “Start Delay” button lights up and goes off when the programme starts. • Once having pressed the “Start/Pause” button, the countdown of the time delay begins. When the programme starts, the start delay indicator light goes off and is replaced by the programme sequence indication. Press the “Start/Pause” button again. The new programme continues at the same position where the previous programme was interrupted. Do not add detergent for this programme. CANCEL (RESET) A RUNNING PROGRAMME BEFORE THE END The “Reset” button cancels a programme before the end. • Press the “Reset” button for at least 3 seconds. Any existing water is drained out before the door can be opened. Whirlpool is a registered trademark of Whirlpool USA Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash. The remaining time indicator can deviate from the values in the table, because it takes into account the household conditions * applicable at that time. To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out. ** *** Reference Programme for Energy Label. ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE PROGRAMME Add detergent as indicated on the front page and as described in the chapter “Detergent and Additives” in your Instructions for Use. Close the door and turn the programme selector to the desired programme and temperature. [. . . ] “Prewash” button • Only for heavily soiled loads (for example sand, granular dirt) sensible. Increases the cycle time by approximately 15 min. “Eco” button • With a modified temperature profile and a slightly prolonged washing duration, the optimum combination of excellent washing result and even lower energy consumption is achieved. “Intensive rinse” button • More water is added and rinse cycle is prolonged. • This option is particularly suitable for areas with very soft water, washing baby linen and helps people with allergies. [. . . ]