User manual WHIRLPOOL AWO 7226 W INSTRUCTION FOR USE

[. . . ] Same as the spin cycle in the “Cotton” programme. Same as the spin cycle in the “Wool” programme. Drain only - no spinning. Alternative method of terminating programme after “Rinse Hold”. ❉ — — — ❉: 1) 2) optional / Yes : dosing required For improved garment care, spin speed is restricted to 1000 rpm in this programme. For improved garment care, spin speed is restricted to 400 rpm in this programme. Whirlpool is a registered trademark of Whirlpool USA 5019 301 05859 Black process 45. 0° 100. 0 LPI 30105859GB. fm Page 2 Wednesday, April 26, 2006 11:49 AM CONSUMPTION DATA Temperature Programme Cotton Cotton*** Cotton Synthetics Synthetics Delicates Daily load Quick wash Wool Handwash Handwash (°C) 95 60 40 60 40 30 40 30 40 40 30 (kg) 5. 0 5. 0 5. 0 2. 5 2. 5 1. 5 3. 0 3. 0 1. 0 1. 0 1. 0 (l) 54** 49 49 50** 45 50 45 40 55 45 45 (kWh) 1. 90 0. 95 0. 60 0. 70 0. 55 0. 50 0. 45 0. 40 0. 60 0. 60 0. 50 Load Water Energy Approx. [. . . ] Programme Duration (hours : minutes)* 2:00 2:20 2:00 1:30 1:15 0:45 1:00 0:30 0:45 0:40 0:40 Terminate the “Rinse hold” option: • Press the “Start/Pause” button; the programme will terminate automatically with the final spin cycle for the present wash programme. • If you do not wish to spin the clothes, turn the programme selector knob to the “Drain” programme and press the “Start/Pause” button. “Variable spin” button • Every programme has a predefined spin speed. • Press the button to set another spin speed. • If spin speed “0” is selected, the final spinning is cancelled but intermediate spin peaks remain during rinse. PROGRAMME START Open the tap and press the “Start/Pause” button. The indication lamp next to the “Start/Pause” button lights up. The programme sequence indicator shows the current programme phase, running from left to right through Wash, Rinse, Spin/ Drain. • When the programme phase is finished, the corresponding indication goes out. Do not add detergent for this programme. CANCEL (RESET) A RUNNING PROGRAMME BEFORE THE END The “Reset” button cancels a programme before the end. • Press the “Reset” button for at least 3 seconds. Any existing water is drained out before the door can be opened. Whirlpool is a registered trademark of Whirlpool USA Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash. The remaining time indicator can deviate from the values in the table, because it takes into account the household * conditions applicable at that time. ** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out. *** Reference Programme for Energy Label. ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE PROGRAMME Add detergent as indicated on the front page and as described in your Instructions for Use. Close the door and turn the programme selector to the desired programme and temperature. [. . . ] Close the door and turn the programme selector to the desired programme and temperature. The indication lamp next to the “Start/Pause” button flashes. SELECT ANY DESIRED OPTION Push the button(s) of any option(s) desired - the respective indication lamp lights up. When the combination of programme and additional option(s) is not possible, the indication lights switch off automatically. [. . . ]