User manual WHIRLPOOL AWO 846 PRODUCT FICHE

[. . . ] A very gentle spin is used in this programme. ❉ ❉ — — — Yes Yes Yes ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — — — — ❉ ❉ — — — ❉ — ❉ — — ❉ — ❉ — — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ max. 1000 1) max. Delicates 30 - 40 °C Feinwäsche 30 - 40 °C Daily load 40 °C Mischwäsche 40 °C Quick wash 30 °C 30 °C Yes max. Wool Cold - 40 °C Wolle Kalt - 40 °C Yes 1000 1) Handwash 30 - 40 °C Handwäsche 30 - 40 °C — — — — — Yes ❉ ❉ — — — ❉ ❉ ❉ ❉ — — — — — — — — — — — — — — — — — ❉ — — — ❉ ❉ — — — ❉ ❉ ❉ ❉ — 400 2) max. 1000 1) Rinse & Spin Spin Gentle Spin Drain Spülen & Schleudern Schleudern Schonschleudern Abpumpen — — — — 7. 0 Same as the last rinse and the final spin in the “Cotton” programme. 7. 0 In this programme spinning is intensive. [. . . ] after — ❉: 1) 2) optional / Yes : dosing required For improved garment care, spin speed is restricted to 1000 rpm in this programme. For improved garment care, spin speed is restricted to 400 rpm in this programme. Whirlpool is a registered trademark of Whirlpool USA 5019 301 06166 Black process 45. 0° 100. 0 LPI 30106166GB. fm Page 2 Friday, April 11, 2008 12:39 PM CONSUMPTION DATA Programme Cotton Cotton with “Eco”*** Cotton Cotton Synthetics Synthetics Delicates Daily load Quick wash Wool Handwash Temperature Load (°C) (kg) 95 7. 0 60 7. 0 60 7. 0 40 7. 0 60 3. 0 40 3. 0 30 1. 5 40 4. 0 30 4. 0 40 1. 0 40 1. 0 Water Energy (l) (kWh) 74** 2. 10 54 1. 19 69 1. 33 69 0. 75 46** 0. 80 42 0. 40 60 0. 50 48 0. 50 48 0. 25 60 0. 55 45 0. 55 Approx. Programme Duration (hours : minutes)* 2:10 2:10 2:20 2:05 1:35 1:20 0:45 1:00 0:30 0:45 0:40 START DELAY The “Start Delay” allows to run the machine at the consumer’s convenience, for example at night when electricity is cheaper. • Select programme, temperature and options. • Press the “Start Delay” button to select the delay time by 1 to 23 hours; • Press the “Start/Pause” button. The indication light next to the “Start Delay” button lights up and the countdown of the delay time begins. • The time delay indication disappears when the programme starts and it is replaced by the remaining programme time. • Once having pressed the “Start/Pause” button, the number of hours preselected can be reduced by pressing again the “Start Delay” button. To cancel the “Start Delay” . . before you press the “Start/Pause” button: • Turn the programme selector to another position or press the “Reset” button. . . after having pressed the “Start/Pause” button: • Press the “Reset” button for at least 3 seconds - the start delay time disappears from the time display. RED INDICATIONS “Service” Lighting up of the “Service” indication can be caused by a fault in an electrical component. Refer to the “Troubleshooting Guide” in your Instructions for Use; if the fault persists, contact our After Sales Service. “Rinse hold” button • The laundry remains in the last rinse water without progressing to the final spin cycle to avoid creasing and prevent colours from changing. • This option is particularly recommended for the programmes “Synthetics”, “Daily load” and “Delicates”. • It is particularly useful if you want to postpone spinning to a later time, or if you want to drain only. Note: The programme stops to “Rinse hold” at the time the “Rinse hold” light in the programme sequence indication is on. The indication lamp next to the “Start/ Pause” button flashes. Terminate the “Rinse hold” option: • Press the “Start/Pause” button; the programme will terminate automatically with the final spin cycle for the present wash programme. • If you do not wish to spin the clothes, turn the programme selector knob to the “Drain” programme and press the “Start/Pause” button. “Variable spin” button • Every programme has a predefined spin speed. • Press the button to set another spin speed. • If spin speed “0” is selected, the final spinning is cancelled but intermediate spin peaks remain during rinse. The water is drained out only. PROGRAMME START Open the tap and press the “Start/Pause” button. [. . . ] The programme sequence indicator shows the current programme phase, running from left to right through Wash, Rinse, Spin/Drain. The time display shows the remaining programme time. Due to variations in load and temperature of inlet water, the remaining time is newly calculated in certain programme phases. If this is the case, an animation appears on the time display. CHANGE PROGRAMME AND/OR OPTIONS AFTER PROGRAMME START 1. [. . . ]