User manual WHIRLPOOL AWO/C 7340 INSTRUCTION FOR USE

[. . . ] Normally to heavily soiled and robust white cotton laundry. Save energy by selecting a lower wash temperature and adding an oxygen-based bleach product, in addition to your detergent. White and pastel shaded garments made of delicate fabrics. Gentle wash programme to avoid graying or yellowing of your laundry. [. . . ] During tumbling, the display will show an animation. The tumbling phase can be stopped at any time either by pressing any button or by rotating the programme selector; the animation will stop and the door will unlock in about 1 minute as indicated on the display. PROGRAMME START Open the tap and press the “Start/Pause” button . The indicator next to the “Start/Pause” button lights up. Load (kg) 4. 0 7. 0 7. 0 7. 0 3. 0 3. 0 1. 5 1. 5 1. 0 7. 0 4. 0 4. 0 7. 0 3. 5 3. 5 3. 0 3. 0 4. 0 Water (l) 48 74** 54 66 46** 42 60 60 45 68 60 40 54 40 40 19 25 52 Energy (kWh) without “Rapid” 0. 50 2. 20 1. 19 0. 75 0. 90 0. 50 0. 65 0. 40 0. 55 0. 80 0. 45 0. 55 0. 84 0. 63 0. 61 0. 45 0. 15 0. 50 Approx. programme duration (hours : minutes) without “Rapid” with “Rapid” 1:00 2:30 2:20 2:05 1:35 1:20 0:50 0:46 0:40 2:20 1:20 1:40 4:00 3:00 *** 3:00 *** 1:00 0:15 1:30 1:35 1:15 1:10 0:55 1:15 - CHILD LOCK Activating the child lock prevents children from starting a wash cycle or changing the settings of a running programme. The child lock cannot be activated or deactivated when the programme selector is in the “Off/O” position. To activate the child lock: • Turn the programme selector to a programme position, or run a programme as usual. • Press the 2 buttons marked with the key symbol simultaneously for at least 3 seconds. A key-like symbol will shortly appear on the display to indicate that the child lock is active. Any time you try to change a programme setting with active child lock, the display will briefly show the key-like symbol. The programme setting cannot be changed anymore. The only change possible is to switch the washer off by turning the programme selector to the “Off/O” position. To deactivate the child lock: • Press again the 2 buttons marked with the key symbol simultaneously for at least 3 seconds. FAILURE INDICATION In case of any failures or irregularities, consult the “Troubleshooting Guide” in your Instructions for Use. “Water tap closed”: no or not sufficient inlet water ”Service”: failure or malfunction of an electrical component ”Clean pump”: waste water is not pumped out. Spin speed on display blinks: unbalance during spinning. 1:10 Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual water supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx. 15°C through the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water supply will lower the energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature. Water and energy consumptions refer to the default setting of the programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also change the consumption data. The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also “Troubleshooting Guide” in your Instructions for Use). * Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature. [. . . ] The new programme continues at the same position where the previous programme was interrupted. Do not add detergent for this programme. ECO MONITOR The „Eco monitor“ gives you a rough feedback about the power consumption of the programme setting you selected. As soon as you turn the programme selector to any programme, the „Eco monitor“ is on. less more CANCEL (RESET) A RUNNING PROGRAMME BEFORE THE END The “Reset/Drain” button cancels a programme before the end. [. . . ]