User manual WHIRLPOOL AWOD050

[. . . ] Brief programme to refresh your laundry. Only woollens, labelled with the Woolmark and identified as machine washable. This programme (40°C) is tested and approved by The Woolmark Company for machine washable wool. Textiles made of linen, silk, wool and viscose marked as “handwashable”. [. . . ] Same as the spin cycle in the “Cotton” programme. Alternative method of terminating programme after “Rinse hold”. Prewash Main Wash Softener Max Spin Speed rpm Max. Max. Coton 95 °C 7. 0 7. 0 i i Yes Yes i i i i – i i i i i i i i i Cotton 40 - 60 °C Coton 40 - 60 °C SuperEco 60 °C SuperEco 60 °C 7. 0 – Yes i i – – i i i Max. Synthetics 30 - 40 - 60 °C Synthétique 30 - 40 - 60 °C 3. 0 1. 5 4. 0 4. 0 1. 0 1. 0 1. 0 – – – 7. 0 7. 0 – i i – – – – – – – – Yes Yes Yes Yes Yes Yes Yes – – – i i i i i i i i – – i i i i i i i i i i i – – – – – – – – – i i – – – – – – – – i – i – – – – i – – i i i i i i i i – – i i i i i i i i i – Max. – Delicates 30 - 40 °C Délicat 30 - 40 °C 40 °C Daily load 40 °C Quick wash 30 °C Chrono 30 °C Wool Cold - 40 °C Laine Froid - 40 °C Handwash 40 °C Lavage main 40 °C Lingerie 30 °C Lingerie 30 °C Rinse & Spin Spin Drain Rinçage + Essorage Essorage Vidange i : option / Yes : dosing required 1) For improved garment care spin speed is restricted in these programmes. The wool and handwash cycles of this machine have been tested and approved by The Woolmark Company for the washing of Woolmark garments labelled as “machine wash” or “hand wash” provided that the garments are washed according to the instructions on the garment label and those issued in this programme chart. M0619 Whirlpool is a registered trademark of Whirlpool USA. 5019 301 01323 CONSUMPTION DATA Programme Temperature (°C) Load (kg) Water (l) Energy (kWh) without “Rapid” Approx. programme duration (hours : minutes) without “Rapid” with “Rapid” Cotton/ Antibacterial 95 7. 0 74* 2. 10 2:10 Cotton ** 60 7. 0 54 0. 91 4:00 2:30 Cotton ** 60 3. 5 40 0. 85 3:00 *** Cotton 40 7. 0 69 0. 80 3:15 2:15 Cotton ** 40 3. 5 40 0. 65 3:00 *** Super Eco 60 7. 0 69 0. 84 4:00 Synthetics 60 3. 0 50* 0. 80 1:35 1:14 Synthetics 40 3. 0 46 0. 50 1:20 0:59 Delicates 30 1. 5 60 0. 50 0:45 Daily load 40 4. 0 45 0. 50 1:00 Quick wash 30 4. 0 45 0. 40 0:30 Wool 40 1. 0 60 0. 50 0:45 Handwash 40 1. 0 45 0. 50 0:40 Lingerie 30 1. 0 45 0. 40 0:36 Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash. Water and energy consumption refer to the default setting of the programmes; selecting special options or modifying spin speed or temperature will change the consumption data. The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also “Troubleshooting Guide” in your Instructions for Use). * To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out. ** Reference programmes for Energy Label. *** Automatic adaptation of programme duration after detection of wash load “Variable spin” button • Every programme has a predefined spin speed. Terminate the “Rinse hold” option: • Press the “Start(Pause)” button; the programme will terminate automatically with the final spin cycle for the present wash programme. • If you do not wish to spin the clothes, turn the programme selector knob to the “Drain” programme and press the “Start(Pause)” button. The “Start delay” allows to run the machine at the consumer’s convenience, for example at night when electricity is cheaper. Do not use liquid detergent when activating “Start delay” option. • Select programme, temperature and options. • Press the “Start delay” button to select the delay time by 1, 3, 6, 9 or 12 hours. • Press the “Start(Pause)” button. The indication next to the “Start delay” button blinks and the countdown of the delay time begins. • The time delay indication disappears when the programme starts and it is replaced by the programme sequence indication. • Once having pressed the “Start(Pause)” button, the delay time can be reduced by pressing again the “Start delay” button. To cancel the “Start delay” . . before you press the “Start(Pause)” button: • Turn the programme selector to another position or press the “Reset” button. . . after having pressed the “Start(Pause)” button: • Press the “Start(Pause)” button - the light of the selected start delay goes off. [. . . ] 3. Open the door and unload the machine. 4. Leave the door ajar to allow the drum to dry. CHANGE PROGRAMME AND/OR OPTIONS AFTER PROGRAMME START Open the tap and press the “Start/Pause” button. The indication lamp next to the “Start/Pause” button lights up. The programme sequence indicator shows the current programme phase, running from left to right through Wash, Rinse, Drain/Spin. [. . . ]