User manual WHIRLPOOL AWOE 10120 PRODUCT FICHE

[. . . ] This by The Woolmark Select spin speed according to the manufacturer's recommendations on the care label. Woollens, labelled with the Woolmark and identified as machine washable, as well as textiles made of — ❉ ❉ ❉ — — — — — — — — ❉ — Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — ❉ ❉ ❉ ❉ — — ❉ ❉ ❉ ❉ ❉ — ❉ ❉ ❉ — — — — — — — — — — — ❉ ❉ ❉ — — — — ❉ ❉ — — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ max. 1000 1) max. — — — — — — — — — — — — — — — — ❉ — heavily soiled laundry. Normally to selecting a lower and robust white cotton an oxygen-based bleach product, in addition to your detergent. [. . . ] • Select programme, temperature and options. • Press the “Start delay” button to select a delay time up to 23 hours. The light of the “Start (Pause)” button blinks. • Press the “Start (Pause)” button . The light of the “Start (Pause)” button is on. The light of the start delay button will keep blinking until the programme starts. • As soon as the programme starts, the start delay on the display is replaced by the remaining programme time, and the light of the “Start delay” button goes off. • Once having pressed the “Start (Pause)” button , the number of hours preselected can be changed by pressing and holding the “Start delay” button. To cancel the “Start delay” . . . before you press “Start (Pause)” : • Turn the programme selector to another position or press the “Reset/Drain” button . . . . after having pressed “Start (Pause)” : • Press “Start (Pause)” - the delay time disappears from the display. Press “Start (Pause)” again to start the selected programme immediately. “DOOR OPEN” INDICATION Before starting and after end of a programme, the lamp lights to show that the door can be opened. • Press the button to set another spin speed. • If you select spin speed “0”, the final spinning is cancelled, and the water is drained out only. However, intermediate spin phases remain during rinse. • If you select “Rinse hold” , the laundry remains in the last rinse water without progressing to the final spin cycle to avoid creasing and prevent colours from changing. Select “Rinse hold” if you want to postpone spinning to a later time or if you want to drain only. Do not leave the laundry to soak in the rinse hold for too long. The programme stops to “Rinse hold” when the “Rinse hold” light in the programme sequence indicator is on. The “Start (Pause)” button light blinks. To terminate the “Rinse hold” by draining the water, without any spinning, press the “Start (Pause)” button . To terminate the programme by spinning the laundry, press the “Spin speed” button to select the desired spin speed and then the “Start (Pause)” button to start the spin cycle. PROGRAMME END • 1. The display shows “End” and the “Door open” indication Turn the programme selector to the “Off/O” position. [. . . ] Any time you try to change a programme setting with active child lock, the display will briefly show the key-like symbol. The programme setting cannot be changed anymore. The only change possible is to switch the washer off by turning the programme selector to the “Off/O” position. To deactivate the child lock: • Press again the 2 buttons marked with the key symbol simultaneously for at least 3 seconds. SELECT ANY DESIRED OPTION Push the button(s) of any option(s) desired - the respective indication lights up. [. . . ]