User manual WHIRLPOOL AWOE 8760 INSTRUCTION FOR USE

[. . . ] 3. 5 This programme includes a prewash cycle – you can add detergent also to the prewash chamber. Slightly to normally soiled bed linen, table linen and underwear, towels, shirts etc. Offers highest economy in energy consumption by prolonged washing duration. Ideal to be run overnight to additionally profit from the more favourable energy rates. [. . . ] Programme Duration (hours : minutes)* 2:10 2:20 2:05 1:35 1:20 0:45 0:45 0:40 2:21 1:30 1:34 4:00 1:00 0:15 • Select the desired programme, temperature, spin speed and option(s), push and hold the “Favourites” button for at least 3 seconds. The lamp next to “Favourites” shortly blinks and then lights up - the programme setting is saved. Next time you want to use your individual programme setting, select the programme, push the “Favourites” button and start by pushing “Start (Pause)” . If you want to replace the saved programme setting by another one, proceed as already described above. START DELAY The “Start delay” allows to run the machine at the consumer’s convenience, for example at night when electricity is cheaper. • Select programme, temperature, spin speed and options. • Press the “Start delay” button to select a delay time from 0:30 to 23:00 hours. • Press the “Start (Pause)” button . The countdown of the delay time begins; the clock symbol next to the delay time and the colon between hours and minutes blink. • The time delay indication disappears when the programme starts and it is replaced by the remaining programme time. To cancel the “Start delay” . . before you press the “Start (Pause)” button: • Select another programme or press the “Reset/Drain” button . . . after having pressed the “Start (Pause)” button: Press the “Reset/Drain” button for at least 3 seconds; the start delay time disappears from the display. • Turn the programme selector to a programme position, or run a programme as usual. intermediate spin peaks remain during rinse. The water is Unsuitable combinations of options are deselected automatically. “Prewash” button • If you select “Rinse hold” , the laundry remains in the last rinse water without progressing to the final spin cycle, to avoid • Only for heavily soiled loads (for example sand, granular dirt) creasing and prevent colours from changing. Increases the cycle time by approximately 15 min. “Rinse hold”, press the “Variable spin” button repeatedly until the • Do not use liquid detergent for the main wash when activating “Rinse hold” symbol on the display lights up. - The wash programme stops to “Rinse hold” when the “Clean+” button “Rinse hold” symbol on the display blinks; the light of • Choose this option if you use an in-wash additive for stain removal “Start (Pause)” blinks as well. (powder, for example “Vanish”) - it will optimize the additive’s - To terminate the “Rinse hold” by draining the water, efficiency to get better wash performance and stain removal. without any spinning, press the “Start (Pause)” button. • Selectable for programmes “Cotton” and “Synthetics”; choose - To terminate the “Rinse hold” by spinning the laundry, press temperature of 30 or 40°C and use with maximum load. the “Variable spin” button to select the desired spin speed • Add an appropriate amount of in-wash additive for stain and then “Start (Pause)” to start the spin cycle. removal (powder) to the main wash chamber, together with - Do not leave the laundry to soak for too long in the “Rinse hold”. [. . . ] In case you have to open it urgently during a running programme, refer to “Reset a running programme before the end”. If you try to start a wash programme and the door is not properly closed, the “Add garment” indication will blink. CHANGE PROGRAMME AND/OR OPTIONS AFTER PROGRAMME START 1. Press the “Start (Pause)” button to pause the programme. Select the new programme, temperature, any options and another spin speed if you want. [. . . ]