User manual WHIRLPOOL AWOE 9511 PROGRAM CHART

[. . . ] If soil level requires, add oxygen-based stain removers. Slightly to normally soiled robust laundry made of cotton, linen, artificial fibres and their blends. — ❉ ❉ ❉ — — — — — — — — ❉ — Yes Yes Yes Yes Yes Yes Yes Yes ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ — ❉ ❉ ❉ ❉ — ❉ ❉ ❉ — — — — — — — — ❉ — — ❉ ❉ — — — — — — — — — — — ❉ ❉ ❉ — — — — — — — — — — — ❉ ❉ ❉ — — — — ❉ ❉ — — ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ ❉ max. 1000 1) max. 9. 0 Normally to heavily soiled towels, underwear, table and bed linen etc. made of cotton and linen. blouses, overalls, 3. 5 Normally soiled or blendsshirts, cotton. made of polyester (Diolen, Trevira), polyamide (Perlon, Nylon) with 2. 5 Curtains and delicate clothing, dresses, skirts, shirts and blouses. [. . . ] • Press the “Start delay” button to select a delay time up to 23 hours. The light of the “Start (Pause)” button blinks. • Press the “Start (Pause)” button . The light of the “Start (Pause)” button is on. The light of the start delay button will keep blinking until the programme starts. • As soon as the programme starts, the start delay on the display is replaced by the remaining programme time, and the light of the “Start delay” button goes off. • Once having pressed the “Start (Pause)” button , the number of hours preselected can be changed by pressing and holding the “Start delay” button. To cancel the “Start delay” . . . before you press “Start (Pause)” : • Turn the programme selector to another position or press the “Reset/Drain” button . . . . after having pressed “Start (Pause)” : • Press “Start (Pause)” - the delay time disappears from the display. Press “Start (Pause)” again to start the selected programme immediately. “DOOR OPEN” INDICATION Before starting and after end of a programme, the lamp lights to show that the door can be opened. As long as a wash programme is running, the door remains locked and must on no account be forced open. In case you have an urgent need to open it during a running programme, refer to “Reset a running programme before the end”. RED INDICATIONS “Service” Lighting up of the “Service” indication can be caused by a fault in an electrical component. Refer to the “Troubleshooting Guide” in your Instructions for Use. If the fault persists, contact our After Sales Service. “Water tap closed” The appliance has no or insufficient water supply. If the indication still lights up, refer to the “Troubleshooting Guide” in the Instructions for Use. “Clean pump” Waste water is not pumped out. Check whether the drain hose is kinked or the filter must be cleaned. In the latter case refer to the Instructions for Use (“Removing the Filter”). Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash. * The time indicated on the display can deviate from the values in the table, because it takes into account the operation conditions applicable at that time. ** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out. [. . . ] Due to variations in load and temperature of inlet water, the remaining time is newly calculated in certain programme phases. If this is the case, an animation appears on the display. CHANGE PROGRAMME AND/OR OPTIONS AFTER PROGRAMME START 1. Press “Start (Pause)” light blinks. Select the new programme, temperature, any options and another spin speed if you want. [. . . ]