User manual WHIRLPOOL C 141 A PROGRAM CHART

[. . . ] The corresponding indicator lamp lights up. “Change programme in progress” Select additional options Press the Start button The selected programme is then memorised (even in the event of power failure). Press the START button for 2 sec. until the Start indicator lamp switches off. Select another programme and press the START button again. Wash cycle - Only open the dishwasher if necessary (Warning: beware of hot steam). [. . . ] Unload the appliance, starting from the lower rack. Switch off the appliance Turn off the water tap, unload the racks Dishwasher loading instructions and racks provided Upper rack: Multi-purpose support (A): 1) Depending on the position, for longhandles utensils, cups and glasses. May be used in three different positions. Crockery holders (B): Depending on the position, for example plates, cups and long-stemmed glasses. Revolving glass support (C): 2) Depending on the position, for example small or long-stemmed glasses. carving forks, knives) must be arranged with the sharp end facing in towards the appliance. depending on the model Half Load: Load the upper rack (see description of Options). Place the cutlery basket (D) in the upper rack. Rack height adjustment (also when loaded): • Lower adjustment: pull out the two rack handles outwards (E) and lower the rack. • Upper adjustment: pull the two handles (E) upwards until the rack clicks into place (Factory setting). The rack must be level on both sides. Removing the top rack to provide clearance for large items of crockery in the bottom rack: Open the rack guide retainers (F) on the right and left and remove the top rack. When the upper rack is in place the retainers must always be closed. Retainer closed Retainer open F F Lower rack: Depending on the model with fixed or tilting plate holders (G). Half Load: Load the lower rack (see description of Options). Greater washing power, particularly for plates and saucepans. Cutlery basket (J) or (H): Some models are provided with a grid (I) that can be fitted onto the cutlery basket to keep items separated. Cutlery basket (D), if provided, for appliances with half load only. not sparkling Rust on cutlery Identifying appliance faults • Not made of stainless steel. • The START indicator lamp flashes. (if provided). • Use suitable glasses. • Use suitable cutlery. • Ensure the filter assembly is not clogged and that there is no interruption to the water supply (if necessary, clean the filters *). Press the START button for 2 seconds, until the START indicator lamp switches off. Select a new programme and press the Start button again. If after carrying out the above checks the malfunction persists or appears again, turn the appliance off and turn off the water supply tap, then call our After-Sales Service (see guarantee). Before contacting our After-Sales Service, take note of the following: • The nature of the fault • The appliance type and model • The service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side. Before using the dishwasher, read the user instructions! ADG 6370 Quick Reference Guide GB Options 3) Programme selector knob Time and failure display Indicates in hours the time remaining until the start of the wash cycle. Switches off when the programme starts and indicates the time remaining in hours and minutes. “F . . . . ” Identification of faults for service technician “Delayed start” button On / Off button The wash cycle can be programmed to start after 1 24 hours. With each successive touch of the button, the delayed start indicator increases by 1 hour, and after 24 returns to 00. The dishwasher will start at the set time. Start button Switches “on” when the dishwasher is operating. [. . . ] The light comes on and goes off at the end of the programme. The “Half Load” function can be used with programmes marked with an *. Indicators Add regeneration salt Only add regeneration salt immediately before starting a wash programme. Antibacterial rinse 4) 5) This function adds an antibacterial rinse at the end of the wash cycle, thereby guaranteeing a perfectly clean and sanitized load. The lamp will light up when the function is activated. If the temperature is not maintained during the antibacterial cycle (e. g. [. . . ]