User manual WHIRLPOOL CB 181 INSTALLATION

[. . . ] Any functional fault must be reported to IKEA After Sales Service as soon as possible. Wait at least two hours before switching the appliance on, to ensure that the refrigerant circuit is fully efficient. The electrical installation and the electrical connection must be carried out by a qualified technician according to the manufacturer's instructions and in compliance with the local safety regulations. Clean the inside of the appliance before using it. [. . . ] € Replacement of any parts of the ice and water dispenser must be carried out using original spare parts provided by the Manufacturer. € Any work on the appliance must be carried out by a qualified technician or the After-sales Service. ENGLISH 6 Product description Carefully read the operating instructions before using the appliance. Refrigerator compartment 1 2 3 4 5 6 7 8 9 Crisper drawers Crisper shelf Shelves / Racks Thermostat unit with light Upper door tray Door trays Bottle rack Removable bottle holder Rating plate (at the side of crisper) 4 3 5 6 Freezer compartment 2 9 1 10 8 7 10 Middle and upper basket (storage area for frozen and deep-frozen food) 1 Lower basket (freezing zone) 1 12 Freezer compartment inner door Least cold zone Intermediate temperature zone Coldest zone Features, technical information and images may vary depending on model 12 1 1 Accessories Egg tray Ice tray 1x 1x First use Connect the appliance to the mains power supply. The ideal temperatures for preserving food have already been set at the factory (3-5/MED). Note: After switching the appliance on, it will be necessary to wait for 2 to 3 hours before a temperature suitable for a standard appliance load is reached. ENGLISH 7 Daily use Operation of the refrigerator and freezer compartment • If the refrigerator compartment of your appliance is fitted with a thermostat box the temperature of both compartments is adjusted using the thermostat knob as shown in figure 1. Move the knob to the position to switch the whole appliance off. € If in addition to the internal thermostat box your appliance also has an external control panel with an adjustment knob, the temperatures of the two compartments must be adjusted separately. The knob of the thermostat inside the refrigerator compartment is used for adjusting the temperature of the refrigerator compartment only (see fig. 1), while the external panel is used to adjust the temperature of the freezer compartment. Removing the baskets (depending on the model) Pull the drawers out as far as they go, then lift slightly and remove. 1 A B C D Thermostat control knob Light button Thermostat position setting notch Light bulb (see instructions near the light bulb) Thermostat on 1/MIN: Low refrigeration level Thermostat on 3-5/MED: Medium refrigeration Thermostat on 7/MAX: Maximum refrigeration Thermostat on : Both refrigeration and illumination are switched off. To remove the light bulb turn anticlockwise as shown in figure 1. ENGLISH 8 Note: The freezer can also be used without the upper drawers, in order to maximise space. For correct operation of the freezer compartment the bottom drawer should not be removed. Ensure that after placing the food on the racks, the freezer door closes properly. Making ice cubes (if provided) Fill the ice cube tray up to 2/3 with water and place in the freezer compartment. Do not use sharp or pointed objects to detach the tray. Cleaning and maintenance Regularly clean the appliance using a cloth and a solution of warm water, with some soft detergent suitable for cleaning the inside of the refrigerator compartment. do not use abrasive detergents or tools. To ensure continuous and correct flow of defrost water, regularly clean the inside of the draining hole on the back of the refrigerator near the fruit and vegetable drawer, using the tool provided (see fig. [. . . ] Leave the freezer door open to allow the frost to melt. 2 only pull out the defrost water drain and place a container under the drain. When the operation is completed, replace the defrost water drain. ENGLISH 9 What to do if… Problem Possible cause Solution Check that: • there isn't a power supply failure • the power plug is correctly inserted in the power socket and the two-pole switch, if present, is in the correct position (on) • the electric circuit safety devices installed in the house are fully functional • the power supply cable is not broken Disconnect the appliance from the electric power supply, check the lamp and replace with a new one if necessary (see "Daily use"). [. . . ]