User manual WHIRLPOOL CLHB 30 NE INSTRUCTION FOR USE

[. . . ] Make sure to comply with the following: The appliance must be disconnected from the power supply before carrying out any installation operation. Installation and maintenance must be carried out by a specialised technician, in compliance with the manufacturer’s instructions and the local safety regulations in force. Do not repair or replace any part of the appliance unless specifically stated in the user manual. The power cable must be long enough for connecting the appliance, fitted in the cabinet, to the power supply. [. . . ] If an oven is installed beneath the hob, make sure the oven is equipped with a cooling system. Do not install the hob above a dishwasher or washing-machine, so that the electronic circuits do not come into contact with steam or moisture which could damage them. In the case of flush-mounted installation, call the After-Sales Service to request assembly of screws kit 4801 211 00112. To remove the hob from the worktop use a screw driver (not supplied) unlocking the springs from the bottom side of the appliance. GB5 ELECTRICAL CONNECTION WARNING Disconnect the appliance from the power supply. Installation must be carried out by qualified personnel who know the current safety and installation regulations. The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the regulations provided in this chapter. The power cable must be long enough to allow the hob to be removed from the worktop. Make sure the voltage specified on the dataplate located on the bottom of the appliance is the same as that of the home. - Connection to the terminal block For the electrical connection, use an H05RR-F cable as specified in the table below. Wires 230 V ~ + 230-240 V ~ + 230 V 3 ~ + 400 V 3N ~ + 400 V 2N ~ + Number x size 3 x 4 mm2 3 X 4 mm2 (Australia only) 230 V 230 V 230 V 230 V 400 V 3N ~ 230 V ~ 230-240 V ~ (Australia only) 230 V ~ (UK only) 5 x 1. 5 mm2 4 x 1. 5 mm2 A B C 400 V 2N ~ 230 V 3 ~ (Belgium only) 400 V 2N ~ (Holland only) 230 V 230 V Important: Based on the wiring diagram (see figure) either keep or remove the metal jumpers between the screws on the terminal block L1-L2 and N1-N2. Make sure all six screws on the terminal block are tightened after connecting the cables. Example of jumper present (left) or removed (right). See the wiring diagram for details (the jumpers can be between L1-L2 and between N1-N2). Connect the yellow/green earth wire to the terminal with the symbol . This wire must be longer than the other wires. Remove the terminal block cover (A), undoing the screw and inserting the cover in the terminal block hinge (B). Insert the power cable in the cable clamp and connect the wires to the terminal block as indicated in the connection diagram located near it. Secure the power cable with the cable clamp. Close the cover (C) and screw it on the terminal block with the previously removed screw. Each time the power is connected, the hob performs an automatic check for a few seconds. If the hob already has a power cable, follow the instructions attached to the cable. Connect the appliance to the power supply by means of a multipole switch with minimum contact gap of 3mm. GB6 230 V 230 V 230 V 230 V 230 V 4 x 1. 5 mm2 INSTRUCTIONS FOR USE Control Panel Description Control panel Timer On/Off Control panel lock the symbols are not active!To select the desired functions, touch the areas below. Cooking zone controls and corresponding display Switching the hob ON/OFF To switch the hob on, press the button for approx. 2 seconds until the cooking zone displays light up. [. . . ] The Service number is also given in the warranty booklet; • your full address; • your telephone number. Attach here one of the two stickers giving the product data, included in the warranty booklet. If any repairs are required, contact an authorised After-Sales Service Centre (to ensure the use of original spare parts and correct repairs). Spare parts are available for 10 years. GB9 POWER LEVEL TABLE Power level Max. [. . . ]