User manual WHIRLPOOL DBRI 6910/01 IN INSTRUCTION FOR USE

[. . . ] S INSTALLATIONSBLAD Avståndet mellan kokkärl och nedre delen av fläkten FÅR INTE VARA UNDER 50 cm för elektriska plattor, och minst 65 cm för gasplattor, eller blandade plattor. Om ett större avstånd än det här specificerade anges i installationsanvisningarna som medföljer gasspisen är det detta avstånd som gäller. Vi rekommenderar att en utbildad fackman kontaktas för installationen. Följ numreringen nedan för monteringen: (1 2 3 . . . . . ). [. . . ] Make sure the lamps are cold before touching them. The hood is not a shelf, therefore do not overload or place objects on it. Do not use or leave the hood without its lamps correctly installed - risk of electric shock. Wear work gloves for all installation and maintenance operations. The product is not suitable for outdoor use. The air sucked by the hood must not be eliminated through the same flue of the heating system or other appliances using gas or other fuels. 5019 318 33312 S N DK FIN GB The mains voltage must match that given on the rating plate located inside the hood. If provided with a plug, connect the hood to a socket complying with the current regulations and located in an accessible area. If it does not have a plug (direct connection to the power supply) or if the plug is not in an accessible place, fit a suitable double-pole switch that ensures complete disconnection from the power supply in category III overvoltage conditions, complying with the installation rules. WARNING: Before reconnecting the hood circuit to the power supply and checking correct operation, always make sure the power cable is correctly fitted and that it was NOT crushed in its housing during installation. Make sure to have this operation carried out by a specialised technician. Electrical connection AFTER-SALES SERVICE Cleaning the hood WARNING!Failure to remove oil/grease (at least once a month) could result in fire. Use a soft cloth with a neutral detergent. Never use abrasive substances or alcohol. Before calling the After-Sales Service 1. Check to see if you can fix the problem yourself (see “Troubleshooting Guide”). Switch the appliance off and then on again to check if the problem has been eliminated. If the problem persists, contact the After-Sales Service. Specify: • the type of fault, • the product model given on the dataplate inside the hood, visible on removing the grease filters, • your full address, • your telephone number and area code, • the Service code (the number under the word SERVICE on the dataplate inside the hood, behind the grease filter). If any repairs are necessary, contact an authorised Service Centre (to ensure the use of original spare parts and correct repair). Failure to comply with these instructions can compromise the safety and quality of the product. Before using the hood Please read these instructions carefully and keep them for future reference, in order to ensure best use of your hood. The packing materials (plastic bags, polystyrene, etc. ) are a potential source of danger and must be kept out of the reach of children. Make sure the hood has not been damaged during transport. Declaration of conformity This product has been designed, manufactured and put on the market in conformity with: - safety objectives of the “Low Voltage” Directive 2006/95/EC (which replaces 73/23/EEC as amended) - protection requirements of “EMC” Directive 89/336/EEC amended by Directive 93/68/EEC. Troubleshooting guide If the hood does not work: • Is the plug properly inserted in the power socket?If the hood is not extracting enough: • Is the right speed selected? [. . . ] During this alarm condition the user can only increase the motor speed (3rd and 4th speed). When the hood temperature returns below the alarm threshold, the motor reverts to the pre-alarm operating condition. 3 minutes after the alarm is tripped, the system again verifies the ambient temperature around the display area: if below 70° C, the pre-alarm operating conditions are restored. 5019 318 33312 S N DK FIN GB Maintenance Important!Always disconnect the hood before cleaning or carrying out maintenance by unplugging it or switching off the power supply. [. . . ]